1.3 Parameter Table
YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide 35
u d: References
Reference parameters are used to set the various frequency reference values during operation.
C5-27
(35CH)
Motor 2 ASR Gain
Switching
Frequency
Sets the frequency for switching between proportional gain 1, 2 and integral
time 1, 2.
Default: 0.0 Hz
Min: 0.0 Hz
Max: 120.0 Hz
139
C5-28
(35DH)
Motor 2 ASR
Integral Limit
Sets the ASR integral upper limit for motor 2 as a percentage of rated load
torque.
Default: 200%
Min: 0%
Max: 400%
139
<10> Default setting is determined by A1-02, Control Method Selection.
<12> Setting range value is dependent on C1-10, Accel/Decel Time Setting Units When C1-10 = 0 (0.01 second units), the setting range becomes
0.00 to 600.00 seconds.
<15> The default setting is determined by E3-01, Motor 2 Control Mode.
<16> Default setting is determined by A1-02, Control Method Selection, and o2-04, Drive Model Selection.
<17> The setting range is 1.00 to 300.0 in CLV.
No.
(Addr.)
Name Description Setting Page
d1: Frequency Reference
d1-01
(280H)
Frequency
Reference 1
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-02
(281H)
Frequency
Reference 2
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-03
(282H)
Frequency
Reference 3
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-04
(283H)
Frequency
Reference 4
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-05
(284H)
Frequency
Reference 5
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-06
(285H)
Frequency
Reference 6
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-07
(286H)
Frequency
Reference 7
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-08
(287H)
Frequency
Reference 8
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-09
(288H)
Frequency
Reference 9
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-10
(28BH)
Frequency
Reference 10
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
No.
(Addr.)
Name Description Setting Page
CLV
V/f
OLV
MV1000ParameterGuide_E_conditional.book 35 ページ ２０１３年１０月１１日 金曜日 午後８時１８分
To Next Page
Loading...
