YASKAWA GA500 series - Page 521

YASKAWA TOEPYAIGA5002A GA500 Programming 521
Serial communication terminals .................................. 508
Setting for termination resistor ................................... 512
Mid point B frequency
Motor 2 parameters................................................. 254
Parameter ............................................................ 249
Mid point B voltage
Motor 2 parameters................................................. 255
Parameter ............................................................ 250
Middle Output Frequency
Motor 2 Parameters ................................................ 254
Parameter ............................................................ 249
Middle Output Frequency Voltage
Motor 2 Parameters ................................................ 254
Parameter ............................................................ 249
Minimum output frequency
Parameter ............................................................ 249
Minimum Output Frequency
Motor 2 Parameters ................................................ 254
Minimum Output Voltage
Motor 2 Parameters ................................................ 254
Parameter ............................................................ 249
Momentary Power Loss
KEB Compensation Time ......................................... 370
Monitors
Display procedure .................................................. 466
Motor
Positive Temperature Coefficient (PTC) Thermistor .......... 357
Wiring................................................................ 502
Motor 2
Base Frequency ..................................................... 254
Base voltage......................................................... 255
Control mode settings.............................................. 253
Leakage Inductance ................................................ 256
Line-to-Line Resistance ........................................... 256
Maximum Output Frequency ..................................... 254
Maximum Output Voltage......................................... 254
Mid point B frequency............................................. 254
Mid point B voltage ................................................ 255
Middle Output Frequency ......................................... 254
Middle Output Frequency Voltage ............................... 254
Minimum Output Frequency...................................... 254
Minimum Output Voltage ......................................... 254
Motor Iron Loss..................................................... 257
Motor Iron-Core Saturation Coefficient 1....................... 257
Motor Iron-Core Saturation Coefficient 2....................... 257
Motor rated power (kW)........................................... 257
No-load Current .................................................... 256
Number of motor poles ............................................ 256
Rated current ........................................................ 255
Rated Slip............................................................ 255
V/f Pattern ........................................................... 253
Motor Code Selection .................................................. 258
Motor Overheating
Operation During Detection of Alarms.......................... 362
Operation During Detection of Faults (PTC Input) ............ 362
Motor Overload
Electric Thermal Protection Operation Time ................... 361
Protection Functions ............................................... 358
Motor parameters........................................................ 250
Motor 2 .............................................................. 255
Motor 2 Iron-Core Saturation Coefficient 1 .................... 257
Motor 2 Iron-Core Saturation Coefficient 2 .................... 257
Motor 2 number of motor poles .................................. 256
Motor 2 rated power (kW) ........................................ 257
Motor Parameters ....................................................... 242
Motor 2 Iron Loss .................................................. 257
Motor 2 Leakage Inductance...................................... 256
Motor 2 Line-to-Line Resistance................................. 256
Motor 2 No-load Current .......................................... 256
Motor 2 rated Current.............................................. 255
Motor 2 Rated Slip ................................................. 255
Motor parameters (induction motors) ................................ 250
Leakage Inductance ................................................ 252
Line-to-Line Resistance ........................................... 251
Motor Iron Loss. .................................................... 252
Motor Iron-Core Saturation Coefficient 1....................... 252
Motor Iron-Core Saturation Coefficient 2....................... 252
Motor rated power (kW)........................................... 253
No-load Current .................................................... 251
Number of motor poles ............................................ 251
Rated current ........................................................ 250
Rated Slip............................................................ 251
Motor Power Unit Selection ........................................... 433
MotorDirect@PowUpWhenUsingKeypad .......................... 436
Multi-step speed operation............................................. 226
Setting procedure ................................................... 226
Multiple-unit connection ............................................... 267
N
No-Load Voltage
Parameter ............................................................ 250
NumOfRunCommands Counter Initial............................... 441
O
oC
Overcurrent Detection Gain....................................... 401
Off-Delay Timer......................................................... 180
Offset frequency
Parameter ............................................................ 240
oH
Alarm Settings ...................................................... 397
oH2
Alarm Settings ...................................................... 397
oH3
Operation During Detection of Alarms.......................... 362
oH4
Operation During Detection of Faults (PTC Input) ............ 362
oL2
Protective function ................................................. 400
On-Delay Timer ......................................................... 180
Ope Select @Keypad is Disconnect .................................. 436
Operation During Momentary Power Loss
KEB ride-thru function ............................................ 364
Operation method selection ....................................... 369
Parameter ............................................................ 369
Speed Search function ............................................. 171
Option card
Parameter ............................................................ 263
oS
Detection level ...................................................... 264
Detection time ...................................................... 265
Operation Select at Overspeed.................................... 263
Output Control........................................................... 424
Output Phase Loss Detection
Protective function ................................................. 399
Overexcitation deceleration
Parameter ............................................................ 408