ABB HT580635 - Tables

Operation Manual / 4 Product description / A150-M56/66/57/67 -
A155-M..
Tables
© Copyright 2018 ABB. All rights reserved. HZTL4032_EN Revision H July 2018
Tables
Table1: Related documents .......................................... 5
Table2: Weights of turbocharger A150-M.. – A155-M..
10
Table3: Fitting the turbocharger, dimensions X, L 16
Table4: Pressure screw tightening torques............ 18
Table5: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 25
Table6: Lubricating oil temperature at the inlet... 26
Table7: Maximum lubricating oil temperature at the
outlet ............................................................................... 27
Table8: Tightening torque(86505).......................... 30
Table9: Expected replacement intervals ................ 36
Table10: Maintenance table ...................................... 39
Table11: Parameters for wet cleaning of compressor
42
Table12: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 45
Table13: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 46
Table14: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 47
Table15: Value table for soaking .............................. 54
Table16: Malfunctions when starting – Delayed
start-up ........................................................................... 57
Table17: Malfunctions when starting – Vibrations 57
Table18: Malfunctions when starting – Rubbing of
rotating parts................................................................. 57
Table19: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 58
Table20: Malfunctions during operation – Speed re-
duces............................................................................... 58
Table21: Malfunctions during operation – Speed in-
creases ........................................................................... 58
Table22: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 59
Table23: Malfunctions during operation – Charge air
pressure too low........................................................... 59
Table24: Malfunctions during operation – Charge air
pressure too high ......................................................... 60
Table25: Malfunctions during operation – Engine
performance losses....................................................... 60
Table26: Malfunction – Turbocharger pumping ..... 61
Table27: Malfunction – Sporadic surge blows ........ 61
Table28: Malfunctions when stopping – Runout
noises............................................................................... 62
Table29: Malfunctions when stopping – Runout
time too short ................................................................ 62
Table30: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 63
Table31: Malfunction of the speed measurement
system – Measured speed too high ........................... 63
Table32: Malfunction of the speed measurement
system – Measured speed too low............................. 63
Table33: Swivel lifting eyes......................................... 66
Table34: Press-off screws........................................... 67
Table35: Dismantling screw ....................................... 67
Table36: Weights of assemblies ................................. 71
Table37: Tightening torques ...................................... 72
Table38: Tightening torques for insulation ............ 73
Table39: 3 press-off screws........................................ 79
Table40: Press-off screws – gas outlet flange........ 80
Table41: Tightening torque (90012-01).................... 85
Table42: Permissible clearances A and B ................. 90
Table43: Permitted nozzle ring compression PD ... 91
Table44: Tightening torque (90012-01) ................... 94
Table45: Tightening torque (51007) ......................... 95
Table46: Tightening torque (79041) ......................... 96
Table47: Tightening torque (72011) .......................... 97
Table48: Permissible clearances N and R............... 100
Table49: Tightening torque (51009)....................... 103
Table50: Tightening torque (51009)....................... 104
Table51: Tightening torque (72051) ........................ 106
Table52: Threaded rod, dimension X ....................... 112
Table53: Permissible clearances A and B ................ 116
Table54: Permitted nozzle ring compression PD .. 117
Page 160 / 161Page 160 / 161