ABB Terra 124 - Page 3

To Next Page

To Previous Page

Operation and installation manual

Terra 94/104/124/184 North America

Main Page

Table of Contents5
About this Document10
Function of this Document10
Target Group10
Revision History10
Language10
Illustrations10
Units of Measurement10
Typographical Conventions11
How to Use this Document11
General Symbols and Signal Words11
Special Symbols for Warnings and Dangers12
Related Documents13
Manufacturer and Contact Data13
Abbreviations13
Terminology14
Orientation Agreements15
Safety16
Liability16
General Safety Instructions16
Responsibilities for the Owner16
Required Qualifications for the Installation Engineer17
Personal Protective Equipment17
Safety Instructions During Installation17
Safety Instructions During Transport18
Safety Instructions for Earthing18
Safety Instructions for Use18
Signs on the EVSE19
Discard the EVSE or Parts of the EVSE19
Cyber Security20
Description21
Type Plate21
Intended Use21
Working Principles23
Terra X4 Variants CC and CJ23
Terra X4 Variant C25
Overview26
Overview of the System26
Overview of the EVSE, Outside27
Overview of the EVSE, Inside28
Overview of the Cable Glands of the Charge Post29
Overview of the Installed EVSE30
Overview of the Cable Management System (Option)30
Authorization to Charge31
Payment Terminal31
Options31
EV Charge Cable, CCS 131
EV Charge Cable, CCS 232
EV Charge Cable, Chademo32
Integrated Payment Terminal32
Cable Management System32
Tilt Sensors33
Power Allocation Strategies34
Sequential Power Allocation34
Concurrent Power Allocation35
Dynamic Allocation 'First in First Served35
Dynamic Power Allocation 'Fair Share36
External Residual-Current Device36
Description of the Touchscreen37
General Description of the Layout37
General Description of the Buttons38
Local Service Portal38
Cloud Service Portal39
Inspection and Transport40
Transport the EVSE to the Site40
Unpacking40
Unpacking Procedure40
Do a Check on the Transport Sensors40
Remove the Cabinet from the Pallet41
Transport the EVSE on the Site41
Hoist the Cabinet41
Move the Cabinet with a Forklift Truck42
Installation44
General Installation Procedure44
Site Preparation44
Prepare the Site44
Control the Space and Airflow Around the Cabinet45
Prepare the Foundation46
Prepare the Foundation - General Procedure46
Prepare a Casted Foundation46
Prepare a Standard Prefabricated Foundation46
Replace the Standard Base with an Alternative Base47
Remove the EVSE from the Base48
Install a Base with Side Entrance48
Install a Base with Reduced Height49
Mechanical Installation49
Mechanical Installation Procedure49
Open the Cable Inlet and Remove the Cable Gland50
Guide the Cables through the Opening in the Cable Guide Plate50
Install the Cabinet on the Foundation50
Electrical Installation51
Electrical Installation Procedure51
Connect the PE Wire51
Connect the Enclosure to the Earth52
Connect the AC Input Wires53
Connect the Ethernet Cable53
Tilt Sensors Installation (Option)54
General Procedure54
Install the Bracket of the Tilt Sensors54
Install the Tilt Sensors55
Connect the Tilt Sensors55
Install a Ferrule on a Wire56
Connect a Wire that Has a Ferrule56
Cable Management System Installation (Option)57
Prepare the Cable Management System57
Mount the Clamp58
Install the Cable Management System58
Prepare for Commissioning58
Operation60
Prepare before Use60
Stop the EVSE if There Is an Emergency60
Reset the EVSE after an Emergency61
Charge Session61
Charge an EV61
Start a Charge Session61
Stop a Charge Session62
Energize the EVSE62
De-Energize the EVSE - General Procedure62
Measure the AC Voltage63
Measure the DC Voltage63
Remove Condensation from the Cabinet64
Local Service Portal Operations65
Start the Local Service Portal65
Set the Configuration Parameters65
Set the OCPP Parameters65
Install New Software66
Close the Local Service Portal66
Maintenance and Cleaning67
Maintenance Schedule67
Clean the Cabinet67
Do a Visual Check of the EVSE68
Replace the Air Inlet Filter68
Replace the Air Outlet Filter69
Access to Parts71
Open the Doors71
Close the Doors71
Remove the Border Covers72
Install the Border Covers73
Troubleshooting74
Troubleshooting Procedure74
Troubleshooting Table74
Technical Data75
EVSE Type75
General Specifications75
Parts Included in the Delivery76
Transport Specifications76
Required Tools for Installation77
Required Parts for Installation77
Torque Specifications78
Operating Conditions78
Noise Level78
Tilt Sensor Specifications78
General Specifications78
Wire Specifications79
Wiring Diagram for the Tilt Sensors79
The Alternative Base with Reduced Height80
Cable Management System Specifications81
Dimensions82
General Dimensions82
Packaged Product82
Mass of the EVSE (Without Packaging Material)83
Center of Gravity83
Floor Space Requirements84
Casted Foundation85
Prefabricated Foundation86
Alternative Base with Side Entrance87
Cable Slack88
Height of User Operable Elements88
Communication Interface Specifications89
EVSE Power Rating90
EVSE Rating During Normal Duty Operation90
EVSE Derating During Normal Duty Operation90
EVSE Rating in Heavy Duty Operation90
EVSE Derating in Heavy Duty Operation90
Harmonics on the Grid91
Terra 18491
Terra 124 and 10493
Terra 9494
AC Input Specifications96
General AC Input Specifications96
AC Input Wires97
Terra 9497
Terra 10497
Terra 12498
Terra 18498
DC Output Specifications98
General Specifications98
Terra 9498
Terra 10499
Terra 124104
Terra 184108
Power Consumption112
In-Rush Current113
Maintenance Schedule for the Service Engineer113
Cleaning Specifications114
Spare Parts114
Appendix116
Declaration of Conformity116

ABB Terra 124 - Page 3

Table of Contents

Other manuals for ABB Terra 124

Related product manuals