TM-F1OP-C1XN-01 xi
Figure 1-1 Power Supply Front Panel- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4
Figure 1-2 Power Supply Rear Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–5
Figure 1-3 Programming and Monitoring SW1 Switch - - - - - - - - - - - - - - - - - - - - - 1–7
Figure 1-4 Programming and Monitoring J2 Connector- - - - - - - - - - - - - - - - - - - - - 1–9
Figure 2-1 Shipping or Storage Carton Label- - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–6
Figure 2-2 AC Input Cover and Strain Relief- - - - - - - - - - - - - - - - - - - - - - - - - - - 2–10
Figure 2-3 Maximum Load Wire Length for 1 V Line Drop- - - - - - - - - - - - - - - - - 2–15
Figure 2-4 Bus Bar Shield - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–17
Figure 2-5 Typical Load Connection Hardware - - - - - - - - - - - - - - - - - - - - - - - - - 2–18
Figure 2-6 Output Voltage Connector with Shield - - - - - - - - - - - - - - - - - - - - - - - 2–20
Figure 2-7 Single Load with Local Sensing (Default) - - - - - - - - - - - - - - - - - - - - - 2–21
Figure 2-8 Single Load with Remote Sensing - - - - - - - - - - - - - - - - - - - - - - - - - - 2–21
Figure 2-9 Multiple Loads with Local Sensing - - - - - - - - - - - - - - - - - - - - - - - - - 2–23
Figure 2-10 Multiple Loads with Remote Sensing- - - - - - - - - - - - - - - - - - - - - - - - 2–23
Figure 2-11 J10 Sense Connector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–25
Figure 2-12 Connecting Remote Sense Lines - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–27
Figure 3-1 Operating Modes- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–3
Figure 3-2 Series Operation of Multiple Supplies- - - - - - - - - - - - - - - - - - - - - - - - 3–12
Figure 3-3 Parallel Operation of Multiple Supplies- - - - - - - - - - - - - - - - - - - - - - - 3–13
Figure 3-4 Split Supply Operation of Multiple Supplies - - - - - - - - - - - - - - - - - - - 3–14
Figure 3-5 Split Supply Operation of Multiple Supplies - - - - - - - - - - - - - - - - - - - 3–15
Figure 4-1 Connecting Programming Sources to J2 Connector - - - - - - - - - - - - - - - - 4–5
Figure 5-1 Programming and Monitoring Calibration Locations- - - - - - - - - - - - - - - 5–4
Figure A-1 Typical Input Current Characteristics, 85-130 Vac Range - - - - - - - - - - - A–7
Figure A-2 Typical Input Current Characteristics, 190-264 Vac Range- - - - - - - - - - - A–7
Figure A-3 Current Derating for Rack Mounted 6 V Models - - - - - - - - - - - - - - - - A–10
Figure A-4 Dimensional Drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–12
Figures
TM-F1OP-C1XN-01.book Page xi Thursday, October 25, 2007 9:04 PM
To Next Page
Loading...
