What to do if error message appears: IO exception with ATI Technologies Axia80-M20 Accessories?
If you receive an IO exception error indicating that a file is being used by another process, it means the selected file for data collection is currently open in another program. Close the file, or change the file name, and then select Collect Streaming again.
What to do if data samples are lost with ATI Technologies Axia80-M20?
If you are experiencing lost data samples, try the following: * Connect the sensor directly to the host computer. * If using a switch, minimize the number of switches between the sensor system and the host. * Disable unnecessary network services. * Use a dedicated measurement computer isolated from the company network. * Avoid logging the Host onto a company network. * Place the sensor on a dedicated Ethernet network with no other devices other than the host computer.
What to do if noise affects the ATI Technologies Axia80-M20 sensor?
If you're experiencing noise issues with the ATI Technologies Axia sensor, it could be due to mechanical vibrations or electrical disturbances, possibly from a poor ground. Ensure the DC supply voltage for the sensor has minimal noise and that the sensor is properly grounded through the installation construction.
How to resolve browser not finding Axia sensor on Ethernet network for ATI Technologies Axia80-M20?
If your browser can't find the Axia sensor on the Ethernet network, clear the Windows computer’s ARP table. You can do this by restarting the computer. Alternatively, if you have administrative privileges, go to the computer’s Start menu, select Run..., and enter “arp –d *”.
How to fix excessive IO exception receive timed out errors with ATI Technologies Axia80-M20?
If you're encountering excessive IO exception errors related to receive timeouts, it indicates an interruption in the Ethernet connection. To resolve this, check the Ethernet cabling and the power supply to the ATI Technologies Axia sensor.
What to do if DHCP is not assigning an IP address for ATI Technologies Accessories?
If DHCP isn't assigning an IP address, it may be due to several reasons: * Ensure the Ethernet LAN is connected during power up. * Verify DHCP is selected as the IP Address Mode on the Communications page. * The DHCP server might be taking too long to respond (over 30 seconds). Remember to power cycle the ATI Technologies Axia sensor after changing any IP Address settings.
What causes hysteresis in ATI Technologies Axia80-M20 Accessories?
Hysteresis in ATI Technologies Accessories is caused by mechanical coupling or internal failure.
What to do if ATI Technologies Axia80-M20 sensor is not streaming measurement data?
Verify the ATI Technologies Accessories sensor is correctly installed. Ensure the robot mounting and tool adapter plates are installed on the proper side of the sensor.
General| Brand | ATI Technologies |
|---|---|
| Model | Axia80-M20 |
| Category | Accessories |
| Language | English |
Defines DANGER, WARNING, CAUTION, and NOTICE notifications used in the manual.
Advises verifying sensor rating for expected loads and awareness of dynamic forces.
Warns against modification, probing openings, overloading, and contacting IP64 seals.
Discusses sensor mounting, tool side attachment, and considerations for interface plates.
Provides guidance on routing the sensor cable, bending radius, and cable management techniques.
Details the process of attaching the sensor to the robot arm and mounting interface plate, including torque values.
Explains the pin assignments for the sensor's M8 and M12 connectors and associated cables.
Outlines the steps for performing an initial and annual accuracy check of the sensor.
Advises on protecting the sensor from moisture, water, and electromagnetic fields to maintain IP64 rating.
Details how to convert raw sensor counts into force and torque values using calibration factors.
Explains the low-pass filter settings, cutoff frequencies, and provides attenuation charts.
Explains how to measure forces and torques at a reference point other than the sensor's origin.
Details the sensor's status code bitmap, describing various error conditions and their meanings.
Explains methods for setting up IP addresses, including static and DHCP configurations.
Provides step-by-step instructions for connecting to the sensor's web pages using Windows networking settings.
Provides access to sensor serial number, calibration details, force/torque units, and tool transformation settings.
Allows viewing and editing the system's Ethernet networking options, including IP settings and RDT.
Stresses the need for periodic calibration to maintain traceability and recommends annual accuracy checks.
Lists symptoms related to powering up issues and their potential causes and resolutions.
Addresses common communication problems, such as IP address assignment and network detection.
Identifies common causes for incorrect force/torque readings, including data streaming, range errors, and noise.
Offers tips to optimize network performance and prevent data loss, such as direct connections and OS optimization.
To Next Page
