Barco DP2K-E series

Barco DP2K-E series

163 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

5. Physical installation

5. PHYSICAL INSTALLATION

About this chapter

This chapter describes how the mechanical and electrical set up of your DP2K-E s eries pr ojector has to be done.

Overview

• Positioning the DP2K-E series projector at port w indow

• Connecting the projector with the power net

• Connecting a UPS to the projector electronics

R5906693 DP2K-E SERIES 19/06/2015

23

Table of Contents

Default Chapter3
- Software License Agreement3
- Table of Contents5
1 Welcome7
- About this Manual8
2 Safety9
- General Considerations10
- Important Safety Instructions11
- Product Safety Labels14
- Light Beam Hazard Distance (HD)15
- HD in Function of the Lens Throw Ratio (TR)17
3 Getting Started19
- Installation Requirements20
- Unpacking the Projector22
- Initial Inspection24
4 Installation Process25
- Installation Process Overview26
5 Physical Installation27
- Positioning the DP2K-E Series Projector at Port Window28
- Projector Tilting29
- Connecting the Projector with the Power Net31
- Connecting a UPS to the Projector Electronics32
6 Lenses & Lens Selection35
- Available Lenses36
- Lens Selection37
- Lens Installation38
- Lens Removal39
- Lens Shift, Zoom & Focus40
7 Input & Communication43
- Introduction44
- Local Keypad45
- Projector Status47
- Cinema Controller49
8 Icmp51
- ICMP Introduction52
- Icmp Hdd54
- ICMP Communication Ports55
- ICMP Source Input Ports57
- ICMP Reset Button and Status Leds62
- ICMP HDD Status Leds63
- ICMP Device Certiﬁcate65
- ICMP Conﬁguration Via Communicator67
- Obtaining the Barco ICMP Certiﬁcate68
- Removing a HDD Form the ICMP69
- Installing a HDD into the ICMP70
9 Communicator Touch Panel73
- Communicator Touch Panel74
- Installing the Touch Panel Interface76
- Repositioning the Touch Panel Interface78
10 Starting up79
- Switching the DP2K-E Series Projector on80
- Switching the DP2K-E Series Projector off81
11 Scheimpﬂug83
- Scheimpﬂug Introduction84
- Scheimpﬂug Adjustment86
- Fixation of the Lens Holder Front Plate88
- Back Focal Length Adjustment90
12 Convergence95
- Convergence Controls96
- Preparing for Convergence Adjustment98
- Converging the Blue Pattern Onto the Red Pattern100
- Converging the Green Pattern Onto the Red Pattern101
- Closing off the Light Processor Compartment102
13 Lamp House103
- Introduction104
- Removal of the Lamp Module105
- Installation of the Lamp House107
- Resetting the Lamp Parameters109
14 Preventative Maintenance Actions111
- Month Maintenance Actions112
- Month Maintenance Actions113
15 Maintenance Procedures115
- Check the Dust Filters116
- Vacuum Cleaning of the Dust Filters117
- Washing and Drying the Dust Filters118
- Cleaning the Lens119
- Cleaning the Exterior of the Projector120
- Authorization to Clear Security Warning on the Projector121
16 Removal and Installation of the Projector Covers123
- Removal of the124
- Removal of the Rear Cover125
- Removal of the Top Cover126
- Removal of the Left Side Cover127
- Removal of the Right Side Cover129
- Removal of the Top Cover Plate of the Light Processor Compartment130
- Removal of the Side Cover Plate of the Light Processor Compartment131
- Installation of the Side Cover Plate of the Light Processor Compartment132
- Installation of the Top Cover Plate of the Light Processor Compartment133
- Installation of the Right Side Cover134
- Installation of the Left Side Cover135
- Installation of the Top Cover137
- Installation of the Rear Cover138
- Installation of the139
17 Speciﬁcations141
- Speciﬁcations of the DP2K-6E142
- Specifications143
- Speciﬁcations of the ICMP144
- Dimensions of the DP2K-E Series Projector146
- Dimensions of the Universal Pedestal147
- Technical Regulations148
18 Pin Conﬁgurations149
- About General Purpose Inputs & Outputs (GPIO)150
- Pin Conﬁgurations of the Cinema Controller Communication Ports152
- Pin Conﬁgurations of the ICMP Communication Ports153
19 Environmental Information157
- Disposal Information158
- Rohs Compliance159
- Hazards161
- Production Address162
- Importers Contact Information163

Other manuals for Barco DP2K-E series

Safety Manual9 pages

Related product manuals

Preview: Barco DP2K-12C

Preview: Barco DP2K-19B

Preview: Barco DP2K-23B

Preview: Barco DP2K-20C

Preview: Barco DP2K-20CLP

Barco DP2K-20CLP

Preview: Barco DP2K-36BLP

Barco DP2K-36BLP

Preview: Barco DP2K-10SLP

Barco DP2K-10SLP

Preview: Barco DP2K-S Series

Barco DP2K-S Series

Preview: Barco DP2K-C Series

Barco DP2K-C Series

Preview: Barco DP2K SLP Series

Barco DP2K SLP Series