Barco DP2K-E series

To Next Page

To Previous Page

11. Scheimpflug

Image 11-12

7. Fasten the lock nut at the lower left of the L e ns Holder. Use a 10mm nut driver.

R5906693 DP2K-E SERIES 19/06/2015

Main Page

Default Chapter3
- Software License Agreement3
- Table of Contents5
1 Welcome7
- About this Manual8
2 Safety9
- General Considerations10
- Important Safety Instructions11
- Product Safety Labels14
- Light Beam Hazard Distance (HD)15
- HD in Function of the Lens Throw Ratio (TR)17
3 Getting Started19
- Installation Requirements20
- Unpacking the Projector22
- Initial Inspection24
4 Installation Process25
- Installation Process Overview26
5 Physical Installation27
- Positioning the DP2K-E Series Projector at Port Window28
- Projector Tilting29
- Connecting the Projector with the Power Net31
- Connecting a UPS to the Projector Electronics32
6 Lenses & Lens Selection35
- Available Lenses36
- Lens Selection37
- Lens Installation38
- Lens Removal39
- Lens Shift, Zoom & Focus40
7 Input & Communication43
- Introduction44
- Local Keypad45
- Projector Status47
- Cinema Controller49
8 Icmp51
- ICMP Introduction52
- Icmp Hdd54
- ICMP Communication Ports55
- ICMP Source Input Ports57
- ICMP Reset Button and Status Leds62
- ICMP HDD Status Leds63
- ICMP Device Certiﬁcate65
- ICMP Conﬁguration Via Communicator67
- Obtaining the Barco ICMP Certiﬁcate68
- Removing a HDD Form the ICMP69
- Installing a HDD into the ICMP70
9 Communicator Touch Panel73
- Communicator Touch Panel74
- Installing the Touch Panel Interface76
- Repositioning the Touch Panel Interface78
10 Starting up79
- Switching the DP2K-E Series Projector on80
- Switching the DP2K-E Series Projector off81
11 Scheimpﬂug83
- Scheimpﬂug Introduction84
- Scheimpﬂug Adjustment86
- Fixation of the Lens Holder Front Plate88
- Back Focal Length Adjustment90
12 Convergence95
- Convergence Controls96
- Preparing for Convergence Adjustment98
- Converging the Blue Pattern Onto the Red Pattern100
- Converging the Green Pattern Onto the Red Pattern101
- Closing off the Light Processor Compartment102
13 Lamp House103
- Introduction104
- Removal of the Lamp Module105
- Installation of the Lamp House107
- Resetting the Lamp Parameters109
14 Preventative Maintenance Actions111
- Month Maintenance Actions112
- Month Maintenance Actions113
15 Maintenance Procedures115
- Check the Dust Filters116
- Vacuum Cleaning of the Dust Filters117
- Washing and Drying the Dust Filters118
- Cleaning the Lens119
- Cleaning the Exterior of the Projector120
- Authorization to Clear Security Warning on the Projector121
16 Removal and Installation of the Projector Covers123
- Removal of the124
- Removal of the Rear Cover125
- Removal of the Top Cover126
- Removal of the Left Side Cover127
- Removal of the Right Side Cover129
- Removal of the Top Cover Plate of the Light Processor Compartment130
- Removal of the Side Cover Plate of the Light Processor Compartment131
- Installation of the Side Cover Plate of the Light Processor Compartment132
- Installation of the Top Cover Plate of the Light Processor Compartment133
- Installation of the Right Side Cover134
- Installation of the Left Side Cover135
- Installation of the Top Cover137
- Installation of the Rear Cover138
- Installation of the139
17 Speciﬁcations141
- Speciﬁcations of the DP2K-6E142
- Specifications143
- Speciﬁcations of the ICMP144
- Dimensions of the DP2K-E Series Projector146
- Dimensions of the Universal Pedestal147
- Technical Regulations148
18 Pin Conﬁgurations149
- About General Purpose Inputs & Outputs (GPIO)150
- Pin Conﬁgurations of the Cinema Controller Communication Ports152
- Pin Conﬁgurations of the ICMP Communication Ports153
19 Environmental Information157
- Disposal Information158
- Rohs Compliance159
- Hazards161
- Production Address162
- Importers Contact Information163

Barco DP2K-E series

Table of Contents

Other manuals for Barco DP2K-E series

Related product manuals