Control Panels Appendix | en 169
Bosch Security Systems, Inc. Installation and System Reference Guide 2016.06 | 08 | F.01U.303.996
22.1.3 B308 address settings
Octo-output module number Corresponding relay numbers
01, 02, 03, 04, 05, 06, 07, 08, 09 11 – 18, 21 – 28, 31 – 38, 41 – 48, 51 – 58,
61 – 68, 71 – 78, 81 – 88, 91-98
10*, 11*, 12*, 13*, 14*, 15*, 16*, 17*, 18*, 19* 101 – 108, 111 – 118, 121 – 128, 131 – 138,
141 – 148, 151 – 158, 161 – 168, 171 – 178,
181 – 188, 191 – 198
20*, 21*, 22*, 23*, 24*, 25*, 26*, 27*, 28*, 29* 201 – 208, 211 – 218, 221 – 228, 231 – 238,
241 – 248, 251 – 258, 261 – 268, 271 – 278,
281 – 288, 291 – 298
30*, 31*, 32*, 33*, 34*, 35*, 36*, 37*, 38*, 39* 301 – 308, 311 – 318, 321 – 328, 331 – 338,
341 – 348, 351 – 358, 361 – 368, 371 – 378,
381 – 388, 391 – 398
40*, 41*, 42*, 43*, 44*, 45*, 46*, 47*, 48*, 49* 401 – 408, 411 – 418, 421 – 428, 431 – 438,
441 – 448, 451 – 458, 461 – 468, 471 – 478,
481 – 488, 491 – 498
50*, 51*, 52*, 53*, 54*, 55*, 56*, 57*, 58*, 59* 501 – 508, 511 – 518, 521 – 528, 531 – 538,
541 – 548, 551 – 558, 561 – 568, 571 – 578,
581 – 588 , 591 – 598
*Supported by the B9512G only.
Tab.22.17: Octo-output module valid relay numbers
22.1.4 D8128D address settings
The D8128D OctoPOPIT has two sets of DIP switches. Use the DIP switches on the top of the
unit (with the terminal strip along the left edge) to set the address for the OctoPOPIT. Use the
DIP switches at the bottom of the unit to enable or disable individual points connected to the
OctoPOPIT. The D82128D connects to the control panel through a B600.
ZONEX 1
(Points 9 -
127
D8128D Address Switches ZONEX 2
(Points 129
– 247)+
9 - 16 ON ON ON ON * 129 - 136
17 - 24 ON ON ON OFF * 137 - 144
25 - 32 ON ON OFF ON * 145 - 152
33 - 40 ON ON OFF OFF * 153 - 160
41 - 48 ON OFF ON ON * 161 - 168
49 - 56 ON OFF ON OFF * 169 - 176
57 - 64 ON OFF OFF ON * 177 - 184
65 - 72 ON OFF OFF OFF * 185 - 192
73 - 80 OFF ON ON ON * 193 - 200
81 - 88 OFF ON ON OFF * 201 - 208
To Next Page
Loading...
