Bosch B9512G - Input Points Wiring with D125 B, D130, or D129; Input Points Wiring with or Without EOL Resistors

Control Panels System wiring diagrams | en 95
Bosch Security Systems, Inc. Installation and System Reference Guide 2016.06 | 08 | F.01U.303.996
18.2 Input points wiring with D125B, D130, or D129
Sw. Aux Pwr
Zone B
Zone A
Pnl Common
Pnl Common
Loop B-
Loop A-
Loop B+
Loop A+
Earth Ground
10
9
5
4
3
8
2
1
7
6
Aux Power
Zone B
Zone A
Common
Loop B-
Loop A-
Loop B+
Loop A+
Earth Ground
Loop A+
Loop A-
Loop B+
Loop B-
10
9
5
4
3
8
2
1
7
6
11
12
13
USB POWER
STATUS
L
I
N
K
ETHERNETUSB
B
A
S
E
T
11
13 14
16
17
19
20
22
12
15
18
21
Quick Flash: Low
BATTERY STATUS
Slow Flash:
Charging
Off: Normal
On: Missing
Low 12.1 VDC
Load Shed 10.2 VDC
EARTH GROUND
COMMON
BATTERY ( - )
+ AUX POWER
BATTERY ( + )
CLASS 2
16.5 VAC 40 VA 60 Hz
TRANSFORMER
10
9
8
7
6
5
4
3
2
1
OUTPUT
B (2)
OUTPUT
A (1)
OUTPUT
C (3)
Do not connect
to a receptacle
controlled by
a switch.
Point 5 Point 6
Point 3 Point 4
Point 1 Point 2 Point 7 Point 8
ON-BOARD POINTS
1 k End-of-line-Resistors Required (P/N 15093130-004),
WARNING!
Multi-Battery
installation requires
Model D122 or D122L
Dual Battery Harness.
Improper installation
can be a fire hazard .
WARNING!
Incorrect wiring will
damage this
equipment.
Devices powered by
any output must be
supervised.
POWER SUPPL
The Power S
refer to the B
The system is intended
panel has been approv
RevPol.
Battery: Replace every 3 to
5 years with one or two
Model D126 or D1218 12V
Lead Acid Batteries.
WARNING!
To prevent risk of shock,
disconnect AC power and
communication lines before
servicing.
All exte
Require
Voltage Ranges: Open 3.7 - 5.0 VDC,
Owner I
be removed by
POINT 1 COM POINT 2 POINT 3 COM POINT 4 POINT 5 COM POINT 6 POINT 7 COM POINT 8
Figure18.20: Input wiring with a D125B and a D129
Callout ᅳ Description
1 ᅳ D125B Dual Class B Initiating Module
2 ᅳ To compatible UL listed two-wire smoke detectors. Refer to the D125B Installation Instructions for a listing of
compatible two-wire smoke detectors.
3 ᅳ D129 Dual Class A Initiation Circuit Module
4 ᅳ For wiring instructions, refer to the D129 Dual Class A Initiation Circuit Module Installation Instructions.
Notice!
Use zero retard except for waterflow devices.
All external connections except Terminal 5 (battery positive) are power limited.
Optionally, for 24 V applications use a UL 1481 listed, regulated, power-limited 24 VDC power
supply with a D130 Relay Module. Refer to the D130 Installation Instructions for correct wiring
requirements.
18.3 Input points wiring with or without EOL resistors
Notice!
For the dual EOL resistor circuit style order ICP-1K22AWG-10, package of 10 1.0 kΩ EOL
resistors.