btsr SMART KTF 2000 - Page 4

Table of contents
- ii - SMART KTF 2000
LANG – Language Selection........................................................................................................................... 3A.21
SENSOR TEST - KTF/100HP Device Test.................................................................................................. 3A.22
COM TEST -KTF/100HP - SMART KTF 2000 Communication Test...................................................... 3A.23
SIGNAL TEST - Test of signals between SMART KTF 2000 and Textile Machine ......................3A.24
NEW - Creating a New Article ........................................................................................................................ 3A.25
MODIFY - Modifying Article Parameters...................................................................................................... 3A.30
READ – Article Reading from KTF/100HP Devices ..................................................................................3A.35
LOAD – Loading Parameters into KTF/100HP Devices........................................................................... 3A.36
ERASE - Erasing an Article from Database................................................................................................ 3A.37
Transferring memory contents between SMART KTF 2000 (Master) and
SMART KTF 2000 (Slave)................................................................................................................................. 3A.38
TENS - Reading the Programmed/Measured yarn Tension value on KTF/100HP ........................... 3A.39
SPEED - Reading the yarn feeding Speed
(in m/min) of a KTF/100HP Device ................................. 3A.40
METER -Measuring the amount of yarn fed by KTF/100HP Devices ................................................... 3A.41
IstLFA - Graphic histogram of the Amount of Yarn Fed
(LFA) ............................................................. 3A.42
BarLFA
- Graphic display of the Amount of Yarn Fed (LFA) on a flat-bed knitting machine ...... 3A.44
LEARN – Learning the amount of yarn absorbed by KTF/100HPs....................................................... 3A.46
3B - SMART KTF 2000 – KTF/RW OPERATION
Preliminary operation for using the SMART KTF 2000 terminal connected to KTF/RW system.................. 3B.3
How to check the software version and the application type............................................................................... 3B.3
Operating Sequences............................................................................................................................................... 3B.4
Functions Available within the SETUP Menu (Configuration)........................................................................... 3B.5
Functions Available within the SETUP Menu (Article Creation & Management) ............................................. 3B.6
Functions Available within the WORK Menu...................................................................................................... 3B.7
Functions Available within the MEASUR Menu ................................................................................................. 3B.8
Functions Available within the CONTROL Environment (TARGET).............................................................. 3B.9
Possible messages during the TARGET function ................................................................................................. 3B.9
Functions Available within the CONTROL Environment (Counter Reading) ................................................ 3B.10
Operating Notes about the TARGET Function.................................................................................................. 3B.11
DEVICE - Numbering the KTF/RW Device................................................................................................... 3B.12
OFFSET - Setting the Device OFFSET.......................................................................................................... 3B.13
APPLIC – Application Selection & Configuration ..................................................................................... 3B.14
KEY_ST - Setting the SETUP menu access Keycode .............................................................................. 3B.16
KEY_TG - Setting the TARGET function access Keycode...................................................................... 3B.17
LANG – Language Selection........................................................................................................................... 3B.18
SENSOR TEST - KTF/RW Device Test ........................................................................................................ 3B.19
COM TEST - KTF/100HP - SMART KTF 2000 Communication Test..................................................... 3B.20
SIGNAL TEST - Test of signals between SMART KTF 2000 and Textile Machine ...................... 3B.21
NEW - Creating a New Article ........................................................................................................................ 3B.22
MODIFY – Modifying Article Parameters ..................................................................................................... 3B.30
READ – Lettura Articolo da Dispositivi KTF/RW........................................................................................ 3B.38
ERASE - Erasing an Article from Database................................................................................................ 3B.39
LINK - Transferring memory contents between SMART KTF 2000 (Master) and SMART KTF 2000
(Slave) ............................................................................................................................................. 3B.40