CASE CONSTRUCTION CX17C - Grease Points (Extension Cylinder); Tightening Torques

240 pages

Save Page as PDF

To Next Page

To Previous Page

6-MAINTENANCE

Greasepoints(Extensioncylinder)

Greasetheextensioncylinderevery10hwithintherst

50h.

Togreasetheextensioncylinder,refertopage6-28.

Tighteningtorques

Checkthetighteningtorquesaftertherst50h.

Tocheckthetighteningtorques,referto6-44.

6-19

Main Page

Table of Contents2
General Information7
Note to the Owner7
Intended Use8
Electro-Magnetic Compatibility (EMC)8
Telematics (Optional)8
Manual Scope and Required Training Level9
Product Identification11
Operator's Manual Storage on the Machine14
Machine Orientation15
Machine Components16
Emissions Overview18
Safety Information21
Signal Word Definitions21
Safety Rules - Utility Precautions22
Safety Rules23
Ecology and Environment32
Hand Signals33
Safety Signs37
Controls and Instruments53
Access to Operator's Platform53
Steps and Access Handles53
Operator's Seat54
Forward Controls56
Left-Hand Side Controls63
Safety Lock Lever64
Engine Speed Control Lever64
Right-Hand Side Controls65
Dozer Blade Control Lever67
Instrument Cluster72
Rearward Controls77
Storage Compartment77
Exterior Controls78
Side Doors78
Battery Disconnect Switch79
Fuel Tank80
Swing Lock Pin81
Operating Instructions83
Starting the Unit83
Anti-Theft Protection83
Starting the Engine85
Bringing the Machine up to Operating Temperature87
Operating the Machine in Hot or Cold Weather88
Operating the Machine89
Lowering the Attachment in the Event of a Failure93
Bucket Replacement94
Hydraulic Control Lever Operating Pattern95
Caution While Using Rubber Tracks98
Stopping the Unit102
Stopping the Engine102
Moving the Unit103
Machine Travel103
Parking the Unit109
Parking the Machine109
Transport Operations111
Road Transport111
Loading the Machine Onto a Transport Trailer111
Preparing for Road Transport113
Tie Downs for Shipping113
Unloading the Machine from a Transport Trailer114
Shipping Transport115
Handling the Machine115
Recovery Transport117
Towing the Machine117
Maintenance119
General Information119
Basic Instructions119
General Specification - Biodiesel Fuels122
Fluids and Lubricants124
Releasing Pressure in the Hydraulic System128
Fuel System Bleeding132
Protecting the Electronic and Electrical Systems During Battery Charging or Welding133
Maintenance Planning134
Maintenance Chart134
Break-In Period136
Fuel Filter136
Travel Reduction Gears136
Grease Points (Bucket)136
Grease Points (Boom and Arm)136
Grease Points (Blade)136
Grease Points (Boom Swing Cylinder)136
Grease Points (Extension Cylinder)137
Tightening Torques137
Every 10 Hours138
Engine Oil Level138
Engine Coolant Level140
Hydraulic Oil Level141
Fuel Filter Water Separator142
Fan and Alternator Drive Belt143
Every 50 Hours144
Grease Points (Bucket)144
Grease Points (Blade)145
Grease Points (Extension Cylinder)146
Track Tension147
Swing Ring Gear149
Fuel Tank150
Every 100 Hours151
Fuel Filter Water Separator151
Every 250 Hours152
Engine Oil and Filter152
Battery155
Grease Points (Boom and Arm)158
Swing Bearing159
Boom Swing Cylinder160
Hydraulic Oil Return Filter161
Tightening Torques162
Every 400 Hours163
Fuel Filter163
Every 500 Hours166
Radiator and Coolers166
Air Cleaner167
Every 750 Hours170
Valve Clearance170
Every 1000 Hours171
Travel Reduction Gears171
Every 1500 Hours172
Injection Nozzle172
Every 2000 Hours173
Engine Coolant173
Hydraulic Oil Suction Filter176
Hydraulic Hoses177
Air Cleaner178
Biodegradable Hydraulic Oil179
Every 3000 Hours181
Injection Timing181
Injection Pump181
Every 5000 Hours182
Hydraulic Oil182
When Necessary184
Working Lights184
Fuel Tank Strainer186
Control Levers186
Plastic and Resin Parts187
Fuse and Relay Locations188
Fuses188
Preparing for Storage189
Periodic Checks190
Starting up the Machine after Storage191
Troubleshooting193
Fault Code Resolution193
Engine - Troubleshooting193
Electrical Systems - Troubleshooting194
Other Systems - Troubleshooting195
Specifications197
Dimensions197
Weights199
Accessories201
Direct Fit Buckets201
Klac Type Buckets202
Auxiliary Hydraulic Circuits203
Quick Coupling System - Klac Type220
Quick Coupling System - Mechanical Pin-Grabber Type228
Hydraulic Oil - Breaker/Auger233
Rotating Beacon234
Fire Extinguisher235

CASE CONSTRUCTION CX17C - Grease Points (Extension Cylinder); Tightening Torques

Table of Contents

Related product manuals