Dell Force10 TeraScale E Series - Page 1209

Quality of Service (QoS) | 1209
Example
Figure 47-3. show cam layer2-qos interface Command Output
Example
Figure 47-4. show cam layer2-qos linecard Command Output
show cam layer3-qos
e
Display the Layer 3 QoS CAM entries.
Syntax
show cam layer3-qos {[linecard number port-set number] | [interface interface]}
[summary]
Parameters
Defaults
No default behavior or values
Command Modes
EXEC
FTOS#show cam layer2-qos interface gigabitethernet 2/0
Cam Port Dot1p Proto SrcMac SrcMask DstMac DstMask Dot1p DSCP Queue
Index Marking Marking
-------------------------------------------------------------------------------------------------------------------------
-------
01817 0 - 0 00:00:00:00:cc:cc 00:00:00:00:ff:ff 00:00:00:00:dd:dd 00:00:00:00:ff:ff - - 7
01818 0 - 0 00:00:00:00:00:c0 00:00:00:00:00:f0 00:00:00:00:00:d0 00:00:00:00:00:f0 - 45 5
01819 0 4 0 00:00:00:a0:00:00 00:00:00:ff:00:00 00:00:00:b0:00:00 00:00:00:ff:00:00 4 - 4
01820 0 - 0x2000 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:b0 ff:ff:ff:ff:ff:ff - - 1
02047 0 - 0 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 - - 0
FTOS#
FTOS#show cam layer2-qos linecard 2 port-set 0
Cam Port Dot1p Proto SrcMac SrcMask DstMac DstMask Dot1p DSCP Queue
Index Marking Marking
----------------------------------------------------------------------------------------------------------------------=--
01817 0 - 0 00:00:00:00:cc:cc 00:00:00:00:ff:ff 00:00:00:00:dd:dd 00:00:00:00:ff:ff - - 7
01818 0 - 0 00:00:00:00:00:c0 00:00:00:00:00:f0 00:00:00:00:00:d0 00:00:00:00:00:f0 - 45 5
01819 0 4 0 00:00:00:a0:00:00 00:00:00:ff:00:00 00:00:00:b0:00:00 00:00:00:ff:00:00 4 - 4
01820 0 - 0x2000 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:b0 ff:ff:ff:ff:ff:ff - - 1
02047 0 - 0 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 - - 0
FTOS#
linecard number
Enter the keyword linecard followed by the line card slot number.
E-Series Range: 0 to 13 on a E1200, 0 to 6 on a E600/E600i, and 0 to 5 on a
E300.
port-set number
Enter the keyword port-set followed by the line card’s port pipe.
Range: 0 or 1
interface interface Enter the keyword interface followed by one of the keywords below and
slot/port or number information:
• For a Fast Ethernet interface, enter the keyword
FastEthernet
followed by the slot/port information.
• For a Gigabit Ethernet interface, enter the keyword
GigabitEthernet
followed by the slot/port information.
• For a SONET interface, enter the keyword
sonet followed by the slot/
port information.
• For a Ten Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet followed by the slot/port information.
summary (OPTIONAL) Enter the keyword summary to display only the total
number of CAM entries.