dynasonics TFX Ultra - Page 2

dynasonics TFX Ultra

120 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Transit Time Meter, TFX Ultra

Page ii May 2016TTM-UM-00136-EN-06

Table of Contents

Default Chapter3
- Table of Contents3
Scope of this Manual7
Unpacking and Inspection7
Safety7
- Terminology and Symbols7
- Considerations7
Quick-Start Operating Overview8
- Transducer Location8
- Electrical Connections8
- Pipe Preparation and Transducer Mounting9
- Initial Settings and Powerup9
Introduction10
- Application Versatility10
- CE Compliance10
- User Safety10
- Data Integrity10
- Product Identification10
Transmitter Installation11
- Transmitter Location11
- Power Connections12
Transducer Installation15
- Select a Mounting Location15
- Select a Mounting Configuration17
- Enter the Pipe and Liquid Parameters19
- Mount the Transducer19
- Transducer Mounting Configurations20
Inputs/Outputs25
- General25
- 4-20 Ma Output25
- Reset Total Input26
- Control Outputs (Flow-Only Model)26
- Rate Alarm Outputs27
- Frequency Output (Flow-Only Model)28
- Totalizer Output Option (Energy Model)29
- RS485 Port30
- Ethernet Port31
- USB Programming Port31
Heat Flow for Energy Model Only31
- Installing Surface-Mounted Rtds31
- Installing Insertion (Wetted) Rtds32
- Wiring Rtds to the Transmitter32
- Replacing Rtds33
Parameter Configuration Using the Keypad34
Startup35
Configuration35
- Menu Structure35
- Basic Menu (BSC)36
- Channel 1 Menu (CH1)41
- Channel 2 Menu (CH2)43
- Options Menu43
- Sensor Menu (SEN)44
- Security Menu (SEC)44
- Service Menu (SER)45
- Service Menu (SER) Continued46
- Display Menu (DSP)47
Parameter Configuration Using Ultralink Software48
- System Requirements48
- Installation48
- Initialization48
Configuration Menu50
- Basic Tab50
- Flow Tab52
- Filtering Tab53
- Output Tab54
- Security Tab58
- Display Tab58
Strategy Menu59
Calibration Menu60
- Remove the Zero Offset60
- Select Flow Rate Units60
- Set Multiple Flow Rates61
- Ultralink Error Codes62
- Target Dbg Data Screen Definitions63
- Saving the Configuration on a PC63
- Printing a Configuration Report63
Menu Maps64
- Basic Menu64
- Channel 1 Menu64
- Channel 2 Menu65
- Sensor Menu65
- Security Menu65
- Service Menu65
- Display Menu65
Communications Protocols66
- Non-Ethernet Module Models66
- Ethernet Module Models66
- Ethernet/Ip67
- TCP Object70
- HEX - 1 Instance)70
- Ethernet Link Object71
- HEX - 1 Instance)71
- Reset Totalizer Object71
- Modbus72
- Bacnet75
- Bacnet Configuration77
- Bacnet Object Support78
- Annex A-Protocol Implementation Conformance Statement (Normative)79
- Annex A-Protocol Implementation Conformance Statement (Normative)81
- Ethernet Port Settings83
- Network Settings87
Troubleshooting88
Heating and Cooling Measurement91
- Rate of Heat Delivery91
In-Field Calibration of RTD Temperature Sensors92
- Equipment Required92
- Replacing or Re-Calibrating Rtds92
Brad Harrison® Connector Option95
Product Labels96
Control Drawings98
CE Compliance Drawings104
K Factors106
- Description106
- Calculating K Factors106
Specifications108
- System108
- Transmitter108
- Transducers109
- Software Utilities109
North American Pipe Schedules110
Fluid Properties115

Related product manuals

Preview: dynasonics TFXL series

dynasonics TFXL series

Badger Meter IS-6000 Doppler