dynasonics TFX Ultra - Bacnet Configuration

120 pages

Save Page as PDF

To Next Page

To Previous Page

BACnet Conguration

To change settings, click Edit to access a category.

Figure 56: BACnet configuration screen

Communications Protocols

Page 77 May 2016 TTM-UM-00136-EN-06

Main Page

Default Chapter3
- Table of Contents3
Scope of this Manual7
Unpacking and Inspection7
Safety7
- Terminology and Symbols7
- Considerations7
Quick-Start Operating Overview8
- Transducer Location8
- Electrical Connections8
- Pipe Preparation and Transducer Mounting9
- Initial Settings and Powerup9
Introduction10
- Application Versatility10
- CE Compliance10
- User Safety10
- Data Integrity10
- Product Identification10
Transmitter Installation11
- Transmitter Location11
- Power Connections12
Transducer Installation15
- Select a Mounting Location15
- Select a Mounting Configuration17
- Enter the Pipe and Liquid Parameters19
- Mount the Transducer19
- Transducer Mounting Configurations20
Inputs/Outputs25
- General25
- 4-20 Ma Output25
- Reset Total Input26
- Control Outputs (Flow-Only Model)26
- Rate Alarm Outputs27
- Frequency Output (Flow-Only Model)28
- Totalizer Output Option (Energy Model)29
- RS485 Port30
- Ethernet Port31
- USB Programming Port31
Heat Flow for Energy Model Only31
- Installing Surface-Mounted Rtds31
- Installing Insertion (Wetted) Rtds32
- Wiring Rtds to the Transmitter32
- Replacing Rtds33
Parameter Configuration Using the Keypad34
Startup35
Configuration35
- Menu Structure35
- Basic Menu (BSC)36
- Channel 1 Menu (CH1)41
- Channel 2 Menu (CH2)43
- Options Menu43
- Sensor Menu (SEN)44
- Security Menu (SEC)44
- Service Menu (SER)45
- Service Menu (SER) Continued46
- Display Menu (DSP)47
Parameter Configuration Using Ultralink Software48
- System Requirements48
- Installation48
- Initialization48
Configuration Menu50
- Basic Tab50
- Flow Tab52
- Filtering Tab53
- Output Tab54
- Security Tab58
- Display Tab58
Strategy Menu59
Calibration Menu60
- Remove the Zero Offset60
- Select Flow Rate Units60
- Set Multiple Flow Rates61
- Ultralink Error Codes62
- Target Dbg Data Screen Definitions63
- Saving the Configuration on a PC63
- Printing a Configuration Report63
Menu Maps64
- Basic Menu64
- Channel 1 Menu64
- Channel 2 Menu65
- Sensor Menu65
- Security Menu65
- Service Menu65
- Display Menu65
Communications Protocols66
- Non-Ethernet Module Models66
- Ethernet Module Models66
- Ethernet/Ip67
- TCP Object70
- HEX - 1 Instance)70
- Ethernet Link Object71
- HEX - 1 Instance)71
- Reset Totalizer Object71
- Modbus72
- Bacnet75
- Bacnet Configuration77
- Bacnet Object Support78
- Annex A-Protocol Implementation Conformance Statement (Normative)79
- Annex A-Protocol Implementation Conformance Statement (Normative)81
- Ethernet Port Settings83
- Network Settings87
Troubleshooting88
Heating and Cooling Measurement91
- Rate of Heat Delivery91
In-Field Calibration of RTD Temperature Sensors92
- Equipment Required92
- Replacing or Re-Calibrating Rtds92
Brad Harrison® Connector Option95
Product Labels96
Control Drawings98
CE Compliance Drawings104
K Factors106
- Description106
- Calculating K Factors106
Specifications108
- System108
- Transmitter108
- Transducers109
- Software Utilities109
North American Pipe Schedules110
Fluid Properties115

dynasonics TFX Ultra - Bacnet Configuration

Table of Contents

Related product manuals