Emerson Powerdrive F300 - 5 Getting Started; Understanding the Display; Keypad Operation; KI-HOA Keypad RTC

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Onboard
PLC
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
Powerdrive F300 User Guide 103
Issue Number: 2
5 Getting started
This chapter introduces the user interfaces, menu structure and security
levels of the drive.
5.1 Understanding the display
The keypad can only be mounted on the drive.
5.1.1 KI-HOA Keypad RTC
The KI-HOA Keypad RTC display consists of two rows of text. The upper
row shows the drive status or the menu and parameter number currently
being viewed. The lower row of the display line shows the parameter
value or the specific trip type. The last two characters on the first row
may display special indications. If more than one of these indications is
active then the indications are prioritized as shown in Table 5-2.
When the drive is powered up the lower row will show the power up
parameter defined by Parameter Displayed At Power-Up (11.022).
Figure 5-1 KI-HOA Keypad RTC
1. Escape button
2. Auto button
3. Start forward
4. Navigation keys (x4)
5. Off / Reset (red) button
6. Enter button
The red stop button is also used to reset the drive.
The parameter value is correctly displayed in the lower row of the
keypad display, see table below.
Table 5-1 Keypad display formats
Table 5-2 Active action icon
5.2 Keypad operation
5.2.1 Control buttons
The keypad consists of:
• Navigation Keys - Used to navigate the parameter structure and
change parameter values.
• Enter / Mode button - Used to toggle between parameter edit and
view mode.
• Escape / Exit button - Used to exit from parameter edit or view
mode. In parameter edit mode, if parameter values are edited and
the exit button is pressed, the parameter value will be restored to the
value it had on entry to edit mode.
Three control buttons are used to select Hand / Off / Auto modes (see
below).
Low battery voltage is indicated by low battery symbol on the keypad
display. Refer to section 3.13.1 Real time clock battery replacement on
page 66 for information on battery replacement.
Figure 5-2 Display modes on page 104, shows an example of moving
between menus and editing parameters.
5.2.2 Hand / Off / Auto
Hand / Off / Auto functions are enabled if Pr 01.052 is set to a non-zero
value, otherwise the keypad buttons are allocated as follows:
• Blue - Forward/Reverse
• Green - Run
• Red - Reset
When Hand / Off / Auto functions are enabled (Pr 01.052 set to either 1,
2 or 3), then the keypad buttons will be allocated as follows:
• Blue - Auto
• Green - Hand
• Red - Off/Reset
The value in Pr 01.052 selects Hand/Off/Auto mode on power-up as
shown in Table 5-3.
Table 5-3 Hand/Off/Auto mode
Display formats Value
IP Address 127.000.000.000
MAC Address 01ABCDEF2345
Time 12:34:56
Date 31-12-11 or 12-31-11
Version number 01.02.02.00
Character ABCD
32 bit number with decimal point 21474836.47
16 bit binary number 0100001011100101
AUTO
Reset
HAND
OFF
1
2
3
4
5
6
NOTE
Active action icon Description
Row
(1=top)
Priority
in row
Accessing non-volatile
media card
11
Alarm active 1 2
Keypad real-time clock
battery low
13
Drive security active and
locked or unlocked
14
User program running 3 1
Keypad reference active 4 1
Pr 01.052 Power up
0 Hand/Off/Auto disabled
1 Auto Mode
2 Off Mode
3 See table Table 5-4
or
NOTE
AUTO
AUTO