Emerson Powerdrive F300 - 6 Basic Parameters; Menu 0: Basic Parameters

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Onboard
PLC
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
Powerdrive F300 User Guide 111
Issue Number: 2
6 Basic parameters
6.1 Menu 0: Basic parameters
Menu 0 is used to bring together various commonly used parameters for basic easy set up of the drive. All the parameters in Menu 0 appear in other
menus in the drive (denoted by {…}). Menus 22 can be used to configure the parameters in Menu 0.
Parameter
Range Default
Type
OL RFC-A RFC-S OL RFC-A RFC-S
00.001
Minimum Reference
Clamp
{01.007} ±VM_NEGATIVE_REF_CLAMP1 Hz / rpm 0 Hz / rpm RW Num US
00.002
Maximum Reference
Clamp1
{01.006} ±VM_POSITIVE_REF_CLAMP1 Hz / rpm
50 Hz: 50.0 Hz
60 Hz: 60.0 Hz
50 Hz: 1500.0
rpm
60 Hz: 1800.0
rpm
RW Num US
00.003 Acceleration Rate 1 {02.011}
±VM_ACCEL_RATE
s to Pr
01.006
±VM_ACCEL_RATE
s to Pr 01.006
20.0 s
to Pr
01.006
20.000 s
to Pr
01.006
RW Num US
00.004 Deceleration Rate 1 {02.021}
±VM_ACCEL_RATE
s to Pr
01.006
±VM_ACCEL_RATE
s to Pr 01.006
20.0 s
to Pr
01.006
20.000 s
to Pr
01.006
RW Num US
00.005 Reference Selector {01.014}
A1 A2 (0),A1 Preset (1), A2 Preset (2), Preset (3),
Keypad (4), Precision (5),
Keypad Ref (6)
A1 A2 (0) RW Txt US
00.006
Symmetrical Current
Limit
{04.007} ±VM_MOTOR1_CURRENT_LIMIT % 110 % 110 % RW Num RA US
00.007
Open-loop Control
Mode / Action On
Enable
{05.014}
Ur S (0),Ur (1),
Fixed (2), Ur Auto (3),
Ur I (4), Square (5),
Current 1P (6)
Ur I (4) RW Txt US
Speed Controller
Proportional Gain Kp1
{03.010}
0.0000 to 200.000
s/rad
0.0300 s/rad RW Num US
00.008
Low Frequency
Voltage Boost
{05.015} 0.0 to 25.0 % 3.0 % RW Num US
Speed Controller
Integral Gain Ki1
{03.011}
0.00 to 655.35
s
2
/rad
0.10 s
2
/rad
RW Num US
00.009
Dynamic V to F Select {05.013} Off (0) or On (1) Off (0) RW Bit US
Speed Controller
Differential Feedback
Gain Kd 1
{03.012}
0.00000 to 0.65535
1/rad
0.00000 1/rad RW Num US
00.010
Motor Rpm {05.004} ±180000 rpm RO Num ND NC PT FI
Speed Feedback
{03.002} ±VM_SPEED rpm RO Num ND NC PT FI
00.011 Output Frequency {05.001} ±VM_SPEED_FREQ_REF Hz RO Num ND NC PT FI
00.012 Current Magnitude {04.001} ±VM_DRIVE_CURRENT_UNIPOLAR A RO Bit ND NC PT FI
00.013
Torque Producing
Current
{04.002} ±VM_DRIVE_CURRENT A RO Bit ND NC PT FI
00.015 Ramp Mode Select {02.004}
Standard (1),
Std boost (2)
Standard (1) Standard (1) RW Txt US
00.017
Digital Input 6
Destination
{08.026} 0.000 to 59.999 0.000 RW Num DE PT US
Current Reference
Filter 1 Time Constant
{04.012} 0.0 to 25.0 ms 1.0 ms RW Num US
00.019 Analog Input 1 Mode {07.007}
4-20mA Low (-4), 20-4mA Low (-3),
4-20mA Hold (-2), 20-4mA Hold (-1),
0-20mA (0), 20-0mA (1), 4-20mA Trip (2),
20-4mA Trip (3), 4-20mA (4), 20-4mA (5),
Volt (6), Therm Short Cct (7), Thermistor (8),
Therm No Trip (9)
4-20mA (4) RW Txt US
00.020
Analog Input 1
Destination
{07.010} 00.000 to 59.999 01.036 RW Num DE PT US
00.021 Analog Input 2 Mode {07.011}
4-20mA Low (-4), 20-4mA Low (-3),
4-20mA Hold (-2), 20-4mA Hold (-1),
0-20mA (0), 20-0mA (1), 4-20mA Trip (2),
20-4mA Trip (3), 4-20mA (4), 20-4mA (5),
Volt (6), Therm Short Cct (7), Thermistor (8),
Therm No Trip (9)
Volt (6) RW Txt US
00.022
Bipolar Reference
Enable
{01.010} Off (0) or On (1) Off (0) RW Bit US
00.024 Preset Reference 1 {01.021} ±VM_SPEED_FREQ_REF Hz / rpm 0.0 Hz / rpm RW Num US
00.025 Preset Reference 2 {01.022} ±VM_SPEED_FREQ_REF Hz / rpm 0.0 Hz / rpm RW Num US
00.026
Preset Reference 3 {01.023}
±VM_SPEED_
FREQ_REF Hz
0.0 Hz RW Num US
Overspeed Threshold
{03.008} 0 to 40000 rpm 0 rpm RW Num US