Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Onboard
PLC
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
Powerdrive F300 User Guide 163
Issue Number: 2
The whole card may be protected from writing or erasing by setting the read-only flag as detailed in section 9.3.9 9888 / 9777 - Setting and clearing
the NV Media Card read only flag on page 164.
The card should not be removed during data transfer, as the drive will produce a trip. If this occurs then either the transfer should be reattempted or in
the case of a card to drive transfer, default parameters should be loaded.
9.3 Transferring data
Data transfer, erasing and protecting the information is performed by entering a code in Pr
mm.000
and then resetting the drive as shown in Table 9-1.
Table 9-1 SMARTCARD and SD card codes
Where yyy indicates the block number 001 to 999.
If the read only flag is set then only codes 6yyy or 9777 are effective.
9.3.1 Writing to the NV Media Card
4yyy - Writes defaults differences to the NV Media Card
The data block only contains the parameter differences from the last
time default settings were loaded.
All parameters except those with the NC (Not copied) coding bit set are
transferred to the NV Media Card. In addition to these parameters all
menu 20 parameters (except Pr 20.000), can be transferred to the NV
Media Card.
Writing a parameter set to the NV Media Card (Pr 11.042 =
Program (2))
Setting Pr 11.042 to Program (2) and resetting the drive will save the
parameters to the NV Media Card, i.e. this is equivalent to writing 4001
to Pr mm.000. All NV Media Card trips apply except 'Card Change'. If
the data block already exists it is automatically overwritten. When the
action is complete this parameter is automatically reset to None (0).
9.3.2 Reading from the NV Media Card
6yyy - Reading from NV Media Card
When the data is transferred back to the drive, using 6yyy in Pr mm.000,
it is transferred to the drive RAM and the EEPROM. A parameter save is
not required to retain the data after-power down. Set up data for any
option modules installed stored on the card are transferred to the drive. If
the option modules installed are different between source and
destination drives, the menus for the option module slots where the
option module categories are different are not updated from the card and
will contain their default values after the copying action. The drive will
produce a 'Card Option' trip if the option module installed to the source
and the destination drives are different or are in different slots. If the data
is being transferred to the drive with different voltage or current rating a
'Card Rating' trip will occur.
The following drive rating dependant parameters (RA coding bit set) will
not be transferred to the destination drive by a NV Media Card when the
voltage rating of the destination drive is different from the source drive
and the file is a parameter file.
However, drive rating dependent parameters will be transferred if only
the current rating is different. If drive rating dependant parameters are
not transferred to the destination drive they will contain their default
values.
Pr 02.008 Standard Ramp Voltage
Pr
04.005
to Pr
04.007
and Pr
21.027
to Pr
21.029
Motoring Current Limits
Pr 04.024, User Current Maximum Scaling
Pr 05.007, Pr 21.007 Rated Current
Pr 05.009, Pr 21.009 Rated Voltage
Pr 05.010, Pr 21.010 Rated Power Factor
Pr 05.017, Pr 21.012 Stator Resistance
Pr 05.018 Maximum Switching Frequency
Pr 05.024, Pr 21.014 Transient Inductance
Pr 05.025, Pr 21.024 Stator Inductance
Pr 06.006 Injection Braking Level
Pr 06.048 Supply Loss Detection Level
Pr 06.065 Standard Under Voltage Threshold
Pr 06.066 Low Under Voltage Threshold
Code Operation SMARTCARD SD card
2001
Transfer the drive parameters to parameter file 001 and sets the block as bootable. This will include the
parameters from attached option modules.
99
4yyy
Transfer the drive parameters to parameter file yyy. This will include the parameters from attached option
modules.
99
5yyy Transfer the onboard user program to onboard user program file yyy.
99
6yyy
Load the drive parameters from parameter file yyy or the onboard user program from onboard user
program file yyy.
99
7yyy Erase file yyy.
99
8yyy
Compare the data in the drive with file yyy. If the files are the same then Pr mm.000 (mm.000) is simply
reset to 0 when the compare is complete. If the files are different a ‘Card Compare’ trip is initiated. All
other NV media card trips also apply.
99
9555 Clear the warning suppression flag
99
9666 Set the warning suppression flag
99
9777 Clear the read-only flag
99
9888 Set the read-only flag
99
9999 Erase and format the NV media card
9
40yyy
Backup all drive data (parameter differences from defaults, an onboard user program and miscellaneous
option data), including the drive name; the store will occur to the </MCDF/driveyyy/> folder; if it does not
exist, it will be created. Because the name is stored, this is a backup, rather than a copy. The command
code will be cleared when all drive and option data have been saved.
9
60yyy
Load all drive data (parameter differences from defaults, an onboard user program and miscellaneous
option data); the load will come from the </MCDF/driveyyy/> folder. The command code will not be
cleared until the drive and all option data have been loaded.
9
To Next Page
Loading...
