Emerson Powerdrive F300 User Manual

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Onboard
PLC
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
Powerdrive F300 User Guide 217
Issue Number: 2
Table 11-5 Defaults for Pr 10.030, Pr 10.031 and Pr 10.061
10.054 Trip 6 Time 00:00:00 to 23:59:59 RO Time ND NC PT PS
10.055 Trip 7 Date 00-00-00 to 31-12-99 RO Date ND NC PT PS
10.056 Trip 7 Time 00:00:00 to 23:59:59 RO Time ND NC PT PS
10.057 Trip 8 Date 00-00-00 to 31-12-99 RO Date ND NC PT PS
10.058 Trip 8 Time 00:00:00 to 23:59:59 RO Time ND NC PT PS
10.059 Trip 9 Date 00-00-00 to 31-12-99 RO Date ND NC PT PS
10.060 Trip 9 Time 00:00:00 to 23:59:59 RO Time ND NC PT PS
10.061 Braking Resistor Resistance 0.00 to 10000.00 Ω See Table 11-5 RW Num US
10.062 Low Load Detected Alarm Off (0) or On (1)
RO Bit ND NC PT
10.063 Local Keypad Battery Low Off (0) or On (1) RO Bit ND NC PT
10.064 Remote Keypad Battery Low Off (0) or On (1) RO Bit ND NC PT
10.065 Auto-tune Active Off (0) or On (1) RO Bit ND NC PT
10.067 Fire Mode Active Off (0) or On (1) RO Bit ND NC PT
10.068 Hold Drive OK On Under Voltage Off (0) or On (1) Off (0) RW Bit US
10.069 Additional Status Bits 0000000000 to 1111111111
RO Bin ND NC PT
10.070 Trip 0 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.071 Trip 1 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.072 Trip 2 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.073 Trip 3 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.074 Trip 4 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.075 Trip 5 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.076 Trip 6 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.077 Trip 7 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.078 Trip 8 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.079 Trip 9 Sub-trip Number 0 to 65535 RO Num ND NC PT PS
10.080 Stop Motor Off (0) or On (1) RO Bit ND NC PT
10.081 Phase Loss Off (0) or On (1) RO Bit ND NC PT
10.101 Drive Status
Inhibit (0), Ready (1), Stop (2), Scan (3),
Run (4), Supply Loss (5), Deceleration (6),
dc Injection (7), Position (8), Trip (9),
Active (10), Off (11),
Hand (12), Auto (13), Heat (14),
Under Voltage (15), Phasing (16)
RO Txt ND NC PT
10.102 Trip Reset Source 0 to 1023 RO Num ND NC PT PS
10.103 Trip Time Identifier -2147483648 to 2147483647 ms RO Num ND NC PT
10.104 Active Alarm
None (0), Brake Resistor (1), Motor
Overload (2),
Ind Overload (3), Drive Overload (4),
Auto Tune (5), Limit Switch (6), Fire Mode
(7), Low Load (8), Option Slot 1 (9), Option
Slot 2 (10), Option Slot 3 (11), Option Slot
4 (12)
RO Txt ND NC PT
10.106 Potential Drive Damage Conditions 0000 to 1111 RO Bin ND NC PT PS
RW Read / Write RO Read only Num Number parameter Bit Bit parameter Txt Text string Bin Binary parameter FI Filtered
ND No default value NC Not copied PT Protected parameter RA Rating dependent US User save PS Power-down save DE Destination
IP IP address Mac Mac address Date Date parameter Time Time parameter SMP Slot,menu,parameter Chr Character parameter Ver Version number
Parameter
Range(
Ú)Default(Ö)
Type
OL RFC-A / S OL RFC-A RFC-S
Drive size Pr 10.030 Pr 10.031 Pr 10.061
3 50 W 3.3 s 75 Ω
4 and 5 100 W 2.0 s 38 Ω
All other ratings and frame sizes 0.000 0.00

Emerson Powerdrive F300 Specifications

General

Series	F300
Input Frequency	50/60Hz
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit
Communication Interfaces	Modbus
Enclosure Rating	IP20
Humidity	5% to 95% non-condensing
Altitude	Up to 1000m without derating