Emerson Powerdrive F300 - Page 204

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Onboard
PLC
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
204 Powerdrive F300 User Guide
Issue Number: 2
Parameter
Range(
Ú)Default(Ö)
Type
OL RFC-A / S OL RFC-A RFC-S
07.001 Analog Input 1 ±100.00 % RO Num ND NC PT FI
07.002 Analog Input 2 ±100.00 % RO Num ND NC PT FI
07.004 Monitored Temperature 1 ±250 °C RO Num ND NC PT
07.005 Monitored Temperature 2 ±250 °C RO Num ND NC PT
07.006 Monitored Temperature 3 ±250 °C RO Num ND NC PT
07.007 Analog Input 1 Mode
4-20 mA Low (-4), 20-4 mA Low (-3), 4-20 mA Hold (-2),
20-4 mA Hold (-1), 0-20 mA (0), 20-0 mA (1),
4-20 mA Trip (2), 20-4 mA Trip (3), 4-20 mA (4),
20-4 mA (5), Volt (6), Therm Short Cct (7), Thermistor (8),
Therm No Trip (9)
4-20 mA (4) RW Txt US
07.008 Analog Input 1 Scaling 0.000 to 10.000 1.000 RW Num US
07.009 Analog Input 1 Invert Off (0) or On (1) Off (0) RW Bit US
07.010 Analog Input 1 Destination 0.000 to 59.999 1.036 RW Num DE PT US
07.011 Analog Input 2 Mode
4-20 mA Low (-4), 20-4 mA Low (-3), 4-20 mA Hold (-2),
20-4 mA Hold (-1), 0-20 mA (0), 20-0 mA (1),
4-20 mA Trip (2), 20-4 mA Trip (3), 4-20 mA (4),
20-4 mA (5), Volt (6), Therm Short Cct (7), Thermistor (8),
Therm No Trip (9)
Volt (6) RW Txt US
07.012 Analog Input 2 Scaling 0.000 to 10.000 1.000 RW Num US
07.013 Analog Input 2 Invert Off (0) or On (1) Off (0) RW Bit US
07.014 Analog Input 2 Destination 0.000 to 59.999 1.037 RW Num DE PT US
07.019 Analog Output 1 Source 0.000 to 59.999 5.001 3.002 RW Num PT US
07.020 Analog Output 1 Scaling 0.000 to 10.000 1.000 RW Num US
07.021 Analog Output 1 Mode Volt (0), 0-20 mA (1), 20-0 mA (2), 4-20 mA (3), 20-4 mA (4) Volt (0) RW Txt
07.022 Analog Output 2 Source 0.000 to 59.999 4.002 RW Num US
07.023 Analog Output 2 Scaling 0.000 to 10.000 1.000 RW Num US
07.024 Analog Output 2 Mode Volt (0), 0-20 mA (1), 20-0 mA (2), 4-20 mA (3), 20-4 mA (4) Volt (0) RW Txt
07.025 Calibrate Analog Input 1 Full Scale Off (0) or On (1) Off (0) RW Bit NC
07.026 Analog Input 1 Fast Update Active Off (0) or On (1) RO Bit ND NC PT
07.027 Analog Input 2 Fast Update Active Off (0) or On (1) RO Bit ND NC PT
07.028 Analog Input 1 Current Loop Loss
Off (0) or On (1)
RO Bit ND NC PT
07.029 Analog Input 2 Current Loop Loss RO Bit ND NC PT
07.030 Analog Input 1 Offset ±100.00 % 0.00 % RW Num US
07.031 Analog Input 2 Offset ±100.00 % 0.00 % RW Num US
07.033 Power Output ±100.0 % RO Num ND NC PT
07.034 Inverter Temperature ±250 °C RO Num ND NC PT
07.035 Percentage Of d.c. Bus Thermal Trip Level 0 to 100 % RO Num ND NC PT
07.036 Percentage Of Drive Thermal Trip Level 0 to 100 % RO Num ND NC PT
07.037 Temperature Nearest To Trip Level 0 to 29999 RO Num ND NC PT
07.038 Temperature Monitor Select 1 0 to 29999 1001 RW Num US
07.039 Temperature Monitor Select 2 0 to 29999 1002 RW Num US
07.040 Analog Input 1 Minimum ±100.00 % -100.00 % RW Num US
07.041 Analog Input 2 Minimum ±100.00 % -100.00 % RW Num US
07.043 Analog Input 1 Maximum ±100.00 % 100.00 % RW Num US
07.044 Analog Input 2 Maximum ±100.00 % 100.00 % RW Num US
07.051 Analog Input 1 Full Scale 0 to 65535 RO Num ND NC PT PS
07.052 Temperature Monitor Select 3 0 to 29999 1 RW Num US
RW Read / Write RO Read only Num Number parameter Bit Bit parameter Txt Text string Bin Binary parameter FI Filtered
ND No default value NC Not copied PT Protected parameter RA Rating dependent US User save PS Power-down save DE Destination