Fagor CNC 8055i FL EN - Page 661

Installation manual
CNC 8055
CNC 8055i
F.
SOFT: V02.2X
·661·
Summary of internal CNC variables.
Variables associated with function G94.
Variables associated with function G94.
Variables associated with function G94.
Variables associated with feedrate override (%)
Coordinate related variables.
Variables associated with electronic handwheels.
FEED R R R Active feedrate at the CNC in mm/min or inch/min.
DNCF R R R/W Feedrate selected via DNC.
PLCF R R/W R Feedrate selected via PLC.
PRGF R R R Feedrate selected by program.
FPREV R R R Active feedrate at CNC, in m/rev or inch/rev.
DNCFPR R R R/W Feedrate selected via DNC.
PLCFPR R R/W R Feedrate selected via PLC.
PRGFPR R R R Feedrate selected by program.
PRGFIN R R R Feedrate selected by program, in 1/min.
FRO R R R Feedrate Override (%) active at the CNC.
PRGFRO R/W R R Override (%) selected by program.
DNCFRO R R R/W Override (%) selected via DNC.
PLCFRO R R/W R Override (%) selected via PLC.
CNCFRO R R R Override (%) selected from the front panel knob.
PLCCFR R R/W R Override (%) of the PLC execution channel.
Variable CNC PLC DNC
( section 13.7 )
PPOS(X-C) R - - Programmed theoretical position value (coordinate).
POS(X-C) R R R Machine coordinates. Real coordinates of the tool base.
TPOS(X-C) R R R Machine coordinates. Theoretical coordinates of the tool base.
APOS(X-C) R R R Part coordinates. Real coordinates of the tool base.
ATPOS(X-C) R R R Part coordinates. Theoretical coordinates of the tool base.
DPOS(X-C) R R R Theoretical position of the probe when the probe touched the part.
FLWE(X-C) R R R Following error of the indicated axis.
DEFLEX R R R Probe deflection along X axis.
DEFLEY R R R Probe deflection along Y axis.
DEFLEZ R R R Probe deflection along Z axis.
DIST(X-C) R/W R/W R Distance traveled by the indicated axis.
LIMPL(X-C) R/W R/W R Second upper travel limit.
LIMMI(X-C) R/W R/W R Second lower travel limit.
DPLY(X-C) R R R Coordinate of the selected axis displayed on the screen.
DRPO(X-C) R R R Position indicated by the Sercos drive of the selected axis.
GPOS(X-C)n p R - - Coordinate of the selected axis, programmed in the (n) block of the program
(p).
Variable CNC PLC DNC
( section 13.8 )
HANPF R R - Pulses received from 1st handwheel since the CNC was turned on.
HANPS R R - Pulses received from 2nd handwheel since the CNC was turned on.
HANPT R R - Pulses received from 3rd handwheel since the CNC was turned on.
HANPFO R R - Pulses received from 4th handwheel since the CNC was turned on.
HANDSE R R For handwheels with a selector button, it indicates whether that button has
been pressed or not.
HANFCT R R/W R Multiplying factor different for each handwheel (when having several).
HBEVAR R R/W R HBE handwheel. Reading enabled, axis being jogged and multiplying factor
(x1, x10, x100).
MASLAN R/W R/W R/W Linear path angle for "Path handwheel" or "Path Jog" mode.
MASCFI R/W R/W R/W Arc center coordinates for "Path handwheel mode" or "Path jog".
MASCSE R/W R/W R/W Arc center coordinates for "Path handwheel mode" or "Path jog".