What to do if my Fischer Panda Portable Generator motor stops by itself?
If your Fischer Panda Portable Generator's motor stops by itself, there could be several reasons. First, ensure that there is enough fuel in the fuel supply system. Second, check the cooling water system flow, including the water pump, inlet water filter, and coolant flow, in case of overheating. Finally, verify the oil level and top it off if needed.
Why is my Fischer Panda Portable Generator producing sooty, black exhaust?
If your Fischer Panda Portable Generator produces sooty, black exhaust, consider these potential causes: * The generator might be overloaded, so reduce the electrical load. * The intake air filter could be blocked, clean it if necessary. * The fuel injector nozzles might be faulty, replace them. * The fuel quality might be poor, try using better quality diesel fuel.
Why is there a drop in the speed of the Fischer Panda Portable Generator motor?
A drop in the speed of the Fischer Panda Portable Generator motor can occur due to several reasons. Make sure that there is not too much oil, drain if needed. Check the fuel supply system, including the fuel filter and fuel pump, and bleed the fuel lines if necessary. Also, verify that there is enough intake air by checking and cleaning the air filter.
What to do if Fischer Panda Portable Generator motor turns over but does not start?
If the motor of your Fischer Panda Portable Generator turns over but doesn't start, there are a few things to investigate. Check the wire connections and circuitry to the stop solenoid valve. Inspect the fuel filter and pump, cleaning them if necessary. Ensure there is an adequate fuel supply. Finally, check the glow plugs and their heating time.
How to fix low output voltage on a Fischer Panda Portable Generator?
If the output voltage of your Fischer Panda Portable Generator is too low, it could be due to the PGMi being overloaded. Try reducing the electrical load by switching off some devices.
What to do if Fischer Panda Portable Generator motor does not turn over when starting?
If the motor of your Fischer Panda Portable Generator doesn't turn over when starting, check if the battery main switch is switched on. Also, verify that the battery voltage is sufficient and that the connection is firm and free of corrosion. Finally, check for starting current faults.
Why does my Fischer Panda Portable Generator motor run irregularly?
Irregular running of the Fischer Panda Portable Generator motor may be due to too much air in fuel lines. Bleed air from fuel system.
Why Fischer Panda Portable Generator motor does not turn over at the normal speed during the starting process?
If the Fischer Panda Portable Generator motor does not turn over at the normal speed during starting, it may be due to insufficient starter battery voltage, check battery. Also, there might be cooling water in the combustion chamber. In that case, turn the generator off, remove the glow plug, rotate the motor by hand carefully, check for water in the oil and change both oil and filter if necessary. Determine the cause for excess water in the combustion chamber, which may be a defective air vent in the cooling water system.
General| Type | Portable Generator |
|---|---|
| Model | 5000i PVK-U |
| Manufacturer | Fischer Panda |
| Rated Power | 4.0 kW |
| Voltage | 230 V |
| Frequency | 50 Hz |
| Fuel Type | Diesel |
| Engine | FPE 320 |
| Number of cylinders | 1 |
| Speed | 3000 rpm |
| Noise Level | 54 dBA (at 7m) |
| Cooling System | Water-cooled |
| Phase | Single-phase |
Essential safety precautions and guidelines for operating the generator safely.
Lists and illustrates the necessary tools for performing maintenance and installation tasks.
Specific safety instructions and hazard warnings related to generator operation and maintenance.
Steps to follow in case of accidents involving electrical shocks from the generator.
Guidance on rescue breathing techniques for an adult who has stopped breathing.
Defines the proper application and intended use of the Fischer Panda generator.
Identifies and describes the main components of the Fischer Panda generator system.
Provides instructions for extended machine downtimes and decommissioning procedures.
Details on interpreting the generator's type plate for identification and specifications.
Visual guide and descriptions of the generator's front, rear, top, and side views.
Explanations of key functional units within the generator system, including cooling and fuel systems.
Specifies the necessary qualifications and conditions for personnel operating the generator.
Highlights potential dangers and safety warnings related to operating the generator.
Provides general guidelines and tips for operating the generator under various conditions.
Defines the qualifications required for personnel performing the generator installation.
Critical safety warnings and precautions to be observed during the installation process.
Guidance on preparing the base and correctly positioning the generator for optimal performance.
Illustrates the standard connection points for various electrical components of the generator.
Instructions and components required for the proper installation of the generator's fuel system.
Guidance on connecting the starter battery and DC system for the generator.
Detailed instructions for installing the generator's cooling system, including radiator placement.
Specifies who is qualified to perform maintenance tasks on the generator.
Highlights safety warnings and precautions essential for performing maintenance.
Instructions for environmentally responsible handling and disposal of materials.
Step-by-step guide on how to check the engine oil level using the oil dipstick.
Detailed procedure for changing the engine oil and replacing the oil filter.
Instructions for checking the condition, electrolyte level, and density of the starter battery.
Guides users through diagnosing and resolving common operational problems with the generator.
Detailed technical specifications for various Panda generator models.
Table listing the diameter specifications for conduits used in vehicle generators.
Guidelines on recommended fuel types and engine oil classifications for optimal performance.
Information on suitable coolants and their recommended mixture ratios with water.
Table specifying cable cross-sections and their corresponding continuous current ratings.
Specifies who is qualified to perform settings and installations on the iControl2 unit.
Essential safety warnings and precautions for using and installing the Panda iControl2 system.
Description of the Panda iControl2 panel, its buttons, and basic functions.
Explanation of the different operating modes available on the Panda iControl2 controller.
Guide to navigating and configuring settings within the iControl2 controller's set-up menu.
Specifies the required qualifications for individuals performing the installation.
Key safety warnings and precautions to ensure a safe installation process.
Instructions for the environmentally sound disposal of electronic components.
Detailed instructions on wiring the iControl2 controller and its terminal assignments.
Critical safety precautions for the operation and handling of the PMGi inverter.
Explanation of the information presented on the PMGi inverter's type plate.
Diagrams and descriptions of the PMGi's front panel and connection interfaces.
Information regarding the back and top sides of the PMGi inverter, including air vents.
Configuration settings for using the PMGi with iGenerators, including Victron software.
Operational guidelines for the PMGi inverter, including remarks on winter operation and load.
Instructions for mounting and electrically connecting the PMGi inverter.
Technical data and specifications for the PMGi generator output and parameters.
To Next Page