Need help?Do you have a question about the Fujitsu PRIMERGY RX2560 M2 and is the answer not in the manual?
Defines the typographical and symbolic conventions used throughout the manual for clarity.
Categorizes maintenance procedures by complexity and required qualification levels.
Provides estimated timeframes for various maintenance tasks, including sub-steps.
Lists the specific tools and screws required for maintenance procedures.
Lists essential documentation and manuals required for maintenance tasks.
Details critical safety precautions for installation, operation, and maintenance.
States compliance with relevant European Community directives.
Provides FCC compliance information for Class A digital devices.
Information on environmentally friendly product design and energy-saving measures.
Explains how to use diagnostic tools to identify defective servers and components.
Provides step-by-step instructions for safely powering down the server.
Details the procedure for safely disconnecting the server's power cord.
Covers initial software steps for maintenance, like suspending BitLocker.
Instructions for disabling the SVOM boot watchdog for maintenance purposes.
Covers post-maintenance software tasks like BIOS updates and verification.
Provides basic details about the server's power supply unit configurations.
Step-by-step guide for installing a power supply unit (PSU).
Instructions for safely removing a power supply unit (PSU).
Procedure for replacing a defective power supply unit (PSU).
Provides an overview of HDDs and SSDs, including configurations and mounting.
Details configurations for 2.5-inch HDD, SSD, and PCIe SSD modules.
Details configurations for 3.5-inch HDD modules.
Information on installing and managing HDD extension boxes.
Procedures for replacing non-hot-plug HDDs and SSDs.
Instructions for installing and replacing SAS expander boards.
Provides basic information about the server's fan modules and airflow.
Step-by-step guide for replacing a system fan module.
Overview of PCIe slots, riser modules, and DynamicLoM slots on the system board.
Instructions for installing and removing PCI slot brackets.
Procedures for installing, removing, and replacing expansion cards and riser cards.
Information on Flash Backup Units (FBUs) and their installation/replacement.
Details on DynamicLoM modules, including installation and software configuration.
Instructions for installing, removing, and replacing the serial interface.
Overview of memory slots, supported capacities, and RAM limits.
Guidelines for populating memory slots based on capacity, rank, and speed.
Details on Independent Channel, Mirrored Channel, and Performance modes.
Step-by-step instructions for installing memory modules.
Instructions for safely removing memory modules.
Procedure for replacing defective memory modules.
Overview of CPU sockets and supported Intel Xeon CPUs.
Detailed steps for installing CPUs, including preparing the air duct.
Instructions for safely removing CPUs and handling electrostatic discharge.
Procedure for upgrading or replacing CPUs, including heat sink installation.
Steps for installing, removing, and replacing CPU heat sinks.
Guide on applying thermal paste to the CPU surface for proper heat dissipation.
Overview of accessible drive bays for optical drives and backup drives.
Procedures for installing accessible drives and mounting brackets.
Instructions for removing accessible drives and dummy covers.
Procedure for replacing defective accessible drives.
Detailed steps for installing and removing slimline ODDs and LSDs in Multibay boxes.
Instructions for installing and removing ultraslim ODDs in 4x 3.5-inch HDD extension boxes.
Procedures for installing and removing ultraslim ODDs in ultraslim ODD adapters.
Step-by-step guide for replacing the front panel module.
Instructions for installing and removing the front VGA connector.
Overview of system board components like CMOS battery, UFM, and TPM.
Instructions for replacing the CMOS battery.
Procedures for installing, removing, and replacing the USB Flash Module (UFM).
Steps for installing, removing, and replacing the Trusted Platform Module (TPM).
Instructions for installing, removing, and replacing the SATA DOM.
Procedures for installing, removing, and replacing the iRMC microSD card.
Instructions for replacing the system board.
Initial steps required before converting a tower server to a rack model.
Detailed procedure for converting the server's form factor.
Final steps after completing the tower to rack model conversion.
A comprehensive list of cables used in the server with their routing information.
Overview of various cabling diagrams for different configurations.
Procedure for replacing the intrusion switch cable.
Instructions for replacing the Out-of-Band (OOB) cable.
Visual identification of server components on the front, rear, and interior.
Detailed information on system board connectors and onboard indicators.
Explanation of jumper settings on the system board for BIOS configuration.
Components and cables required for the minimum server startup configuration.
To Next Page
General