GE ALPS - Page 348

To Next Page

To Previous Page

E-

ALPS Advanced Line Protection System GE Power Management

E.1 FIGURES AND TABLES APPENDIX E

ure 4–3: PHASE TO GROUND TEST CONNECTIONS.............................................................................................................. 4-12

ure 5–1: PHASE-TO-PHASE TEST CONNECTIONS ................................................................................................................... 5-6

ure 5–2: GROUND REACH TIMER TEST CONNECTIONS ......................................................................................................... 5-7

ure 5–3: PHASE-REACH TIMER TEST CONNECTIONS ........................................................................................................... 5-18

ure 8–1: ALPS KEYPAD ................................................................................................................................................................ 8-1

ure 8–2: MODEM CABLE ............................................................................................................................................................ 8-23

ure 8–3: 25-PIN NULL MODEM CABLE ...................................................................................................................................... 8-23

ure 8–4: 25-PIN NULL MODEM CABLE ...................................................................................................................................... 8-27

ure 8–5: NULL MODEM CABLE FOR PORT PL1 ....................................................................................................................... 8-27

ure 10–1: FILE AND EDIT MENUS.............................................................................................................................................. 10-1

ure 10–2: ADDITIONAL ALPS-TEST MENUS............................................................................................................................. 10-1

ure 10–3: ENTER VALUE DIALOG BOX..................................................................................................................................... 10-2

ure 10–4: INPUT TEST DIALOG BOX: M1 PHASE UNITS – ZONE 1........................................................................................ 10-3

ure 10–5: M1 PHASE UNITS – ZONE 1 DIALOG BOX...............................................................................................................10-3

ure 10–6: MT PHASE UNITS – ZONE 2 DIALOG BOX............................................................................................................... 10-4

ure 10–7: M3 PHASE UNITS – ZONE 3 DIALOG BOX...............................................................................................................10-4

ure 10–8: M4 PHASE UNITS – ZONE 4 DIALOG BOX...............................................................................................................10-5

ure 10–9: MOB PHASE UNIT DIALOG BOX............................................................................................................................... 10-5

ure 10–10: M1G GROUND UNITS – ZONE 2 DIALOG BOX ...................................................................................................... 10-6

ure 10–11: MTG GROUND UNITS – ZONE 2 DIALOG BOX...................................................................................................... 10-6

ure 10–12: M3G GROUND UNITS – ZONE 3 DIALOG BOX ...................................................................................................... 10-7

ure 10–13: FILE MENU................................................................................................................................................................ 10-8

ure 10–14: EDIT MENU ............................................................................................................................................................. 10-11

ure 10–15: VIEW MENU ............................................................................................................................................................ 10-12

ure 10–16: ALPS TEST TOOLBAR ........................................................................................................................................... 10-12

ure 10–17: ALPS TEST STATUS BAR ...................................................................................................................................... 10-12

ure 10–18: TOOL SETUP DIALOG BOX................................................................................................................................... 10-13

ure 10–19: WINDOW MENU......................................................................................................................................................10-15

ure 10–20: HELP MENU............................................................................................................................................................ 10-16

ure 10–21: ABOUT ALPS_TST DIALOG BOX .......................................................................................................................... 10-16

ure 11–1: SUPPORTED ARCHITECTURE .................................................................................................................................11-2

ure 11–2: GE POWER MANAGEMENT WELCOME SCREEN................................................................................................... 11-3

ure 11–3: ALPS SOFTWARE INSTALLATION WELCOME SCREEN ........................................................................................ 11-4

ure 11–4: ALPS-LINK TOOLBAR ................................................................................................................................................ 11-5

ure 11–5: ALPS-LINK STATUS BAR...........................................................................................................................................11-5

ure 11–6: PORT SETUP DIALOG BOX....................................................................................................................................... 11-6

ure 11–7: MODEM SETUP DIALOG BOX................................................................................................................................... 11-6

ure 11–8: PRINTER SETUP DIALOG BOX................................................................................................................................. 11-7

ure 11–9: DEVICE SETUP DIALOG BOX ................................................................................................................................... 11-8

ure 11–10: PROTECTION CATEGORY SCROLL LIST ............................................................................................................ 11-11

ure 11–11: REPORT MENU WITH OPEN REPORT ................................................................................................................. 11-14

ure 13–1: LOGIC PROCESSING DELAY.................................................................................................................................... 13-1

ure 13–2: LATCH AND TRUTH TABLE....................................................................................................................................... 13-2

ure 13–3: PICKUP/DROPOUT TIMER ........................................................................................................................................13-2

ure 13–4: PICKUP DELAY TIMER............................................................................................................................................... 13-3

ure 13–5: COUNTER ................................................................................................................................................................... 13-3

ure 13–6: CREATING A NEW FILE............................................................................................................................................. 13-9

ure 13–7: CONTACT CONVERTER INPUTS (CC) ..................................................................................................................... 13-9

ure 13–8: INVERTED CC INPUTS ............................................................................................................................................ 13-10

ure 13–9: INPUT, OPERATOR, AND OUTPUT ICONS ............................................................................................................ 13-10

ure 13–10: STRAIGHT AND ORTHO-CONNECTION ICONS .................................................................................................. 13-10

ure 13–11: SAMPLE BREAKER FAILURE LOGIC.................................................................................................................... 13-11

ure 14–1: NEW SETTINGS DIALOG BOX ..................................................................................................................................14-1

ure 14–2: CHANGE MODEL NUMBER ITEM DIALOG BOX ......................................................................................................14-1

ure 14–3: SELECT PROTECTION SCHEME DIALOG BOX....................................................................................................... 14-2

ure 14–4: CHANGE SETTINGS – PROTECTION DIALOG BOX................................................................................................14-2

ure 14–5: CHANGE SETTING VALUE DIALOG BOX................................................................................................................. 14-2

ure 14–6: SELECT CATEGORIES TO PRINT DIALOG BOX ..................................................................................................... 14-3

ure 14–7: TOOL SETUP DIALOG BOX....................................................................................................................................... 14-3

ure 14–8: ABOUT ALPS-SET DIALOG BOX...............................................................................................................................14-4

ure D–1: SET KEYPAD MENU ......................................................................................................................................................D-1

ure D–2: ACT KEYPAD MENU......................................................................................................................................................D-2

ure D–3: INF KEYPAD MENU .......................................................................................................................................................D-3

Main Page

GE ALPS - Page 348

Table of Contents

Related product manuals