GE ALPS - List of Tables; E.1.2 List of Tables

GE Power Management ALPS Advanced Line Protection System E-
3
APPENDIX E E.1 FIGURES AND TABLES
E
E.1.2 LIST OF TABLES
T
ABLE
: 1–1 ORDER CODES............................................................................................................................................................... 1-3
T
ABLE
: 1–2 ALPS MEASUREMENT FUNCTIONS ............................................................................................................................. 1-5
T
ABLE
: 1–3 ALPS DEFAULT CONTACT CONVERTER ASSIGNMENTS: SINGLE PHASE MODEL................................................ 1-9
T
ABLE
: 1–4 ALPS DEFAULT CONTACT CONVERTER ASSIGNMENTS: THREE PHASE MODEL................................................. 1-9
T
ABLE
: 1–5 ALPS DEFAULT OUTPUT CONTACT ASSIGNMENTS: SINGLE PHASE MODEL ..................................................... 1-10
T
ABLE
: 1–6 ALPS DEFAULT OUTPUT CONTACT ASSIGNMENTS: THREE PHASE MODEL ...................................................... 1-10
T
ABLE
: 1–7 CHANNEL KEYING FOR PILOT TRIPPING (TWO CHANNELS) ................................................................................. 1-38
T
ABLE
: 1–8 SINGLE POLE PHASE A TRIP LOGIC.......................................................................................................................... 1-39
T
ABLE
: 1–9 REPEAT KEYING LOGIC .............................................................................................................................................. 1-39
T
ABLE
: 1–10 CHANNEL KEYING FOR PILOT TRIPPING (FOUR CHANNELS).............................................................................. 1-40
T
ABLE
: 1–11 PILOT KEYING (4 CHANNEL) LOGIC......................................................................................................................... 1-40
T
ABLE
: 2–1 NUM_TC SETTING (SINGLE PHASE MODELS)............................................................................................................ 2-3
T
ABLE
: 2–2 NUM_TC SETTING (THREE PHASE MODELS)............................................................................................................. 2-3
T
ABLE
: 2–3 SETTING FORMAT FOR NUM_MON (SINGLE PHASE TRIPPING MODELS).............................................................. 2-4
T
ABLE
: 2–4 SETTING FORMAT FOR NUM_MON (THREE PHASE TRIPPING MODELS)............................................................... 2-4
T
ABLE
: 2–5 OSCILLOGRAPHY CYCLES PER STORAGE EVENT ................................................................................................... 2-6
T
ABLE
: 2–6 CONTACT CONVERTER ASSIGNMENT FOR PHASE IDENTIFIED CHANNEL SCHEME .......................................... 2-8
T
ABLE
: 2–7 PROPOSED SETTINGS FOR BLOCKING SCHEME.................................................................................................... 2-23
T
ABLE
: 2–8 OUTPUT ASSIGNMENT FOR HYBRIDP SCHEME...................................................................................................... 2-46
T
ABLE
: 2–9 INDEX NUMBERS – CONTACT CONVERTER INPUT ASSIGNMENT........................................................................2-51
T
ABLE
: 2–10 INDEX NUMBERS – SCHEME, RECLOSER, & PROGRAMMABLE LOGIC.............................................................. 2-52
T
ABLE
: 2–11 PROTECTION SETTINGS GUIDE............................................................................................................................... 2-57
T
ABLE
: 2–12 GENERAL SETTINGS GUIDE..................................................................................................................................... 2-64
T
ABLE
: 2–13 PROTECTION SETTINGS DATA SHEET ................................................................................................................... 2-66
T
ABLE
: 2–14 GENERAL SETTINGS DATA SHEET.......................................................................................................................... 2-73
T
ABLE
: 3–1 JUMPER POSITION......................................................................................................................................................... 3-7
T
ABLE
: 4–1 FACTORY DEFAULT COMMUNICATIONS PARAMETERS........................................................................................... 4-5
T
ABLE
: 4–2 DIGITAL OUTPUTS TEST CONNECTIONS.................................................................................................................... 4-8
T
ABLE
: 4–3 ........................................................................................................................................................................................ 4-12
T
ABLE
: 5–1 .......................................................................................................................................................................................... 5-6
T
ABLE
: 5–2 ........................................................................................................................................................................................ 5-18
T
ABLE
: 6–1 TEST CURRENT RANGES FOR PHASE-TO-GROUND REACH................................................................................. 6-11
T
ABLE
: 6–2 TEST CURRENT RANGES FOR PHASE-TO-PHASE REACH..................................................................................... 6-15
T
ABLE
: 8–1 PASSWORD ENCRYPTION KEY TABLE ..................................................................................................................... 8-21
T
ABLE
: 8–2 KEYPAD / DISPLAY INTERFACE ERROR MESSAGES .............................................................................................. 8-22
T
ABLE
: 8–3 HARDWARE SWITCH DESCRIPTIONS ....................................................................................................................... 8-24
T
ABLE
: 8–4 COMMAND SEQUENCE SENT TO MODEM................................................................................................................ 8-25
T
ABLE
: 8–5 CONFIGURATION SETTINGS FOR THE MODEM CONNECTED TO THE RELAY .................................................... 8-26
T
ABLE
: 8–6 MODEM COMMANDS FOR COMMUNICATION BETWEEN RELAY AND PC ............................................................ 8-27
T
ABLE
: 9–1 COMPONENTS TESTED DURING START-UP TESTS.................................................................................................. 9-2
T
ABLE
: 9–2 RUN-TIME BACKGROUND SELF-TESTS ...................................................................................................................... 9-2
T
ABLE
: 9–3 RUN-TIME FOREGROUND SELF-TESTS...................................................................................................................... 9-2
T
ABLE
: 9–4 SYSTEM STATUS ERROR MESSAGES ........................................................................................................................ 9-3
T
ABLE
: 10–1 INPUT QUANTITIES .................................................................................................................................................... 10-2
T
ABLE
: 12–1 OSCILLOGRAPHY DATA STRUCTURE..................................................................................................................... 12-1
T
ABLE
: 12–2 ASCII COMMAND LIST .............................................................................................................................................. 12-2
T
ABLE
: 13–1 PICKUP DELAY TIMER TRUTH TABLE...................................................................................................................... 13-3
T
ABLE
: 13–2 CONTACT CONVERTER INPUT FLAGS.................................................................................................................... 13-4
T
ABLE
: 13–3 CONFIGURABLE INPUTS........................................................................................................................................... 13-4
T
ABLE
: 13–4 SCHEME LOGIC AND RECLOSER OUTPUTS .......................................................................................................... 13-5
T
ABLE
: 13–5 SCHEME LOGIC INPUTS............................................................................................................................................ 13-6
T
ABLE
: 13–6 DISTANCE UNITS........................................................................................................................................................ 13-6
T
ABLE
: 13–7 CURRENT AND VOLTAGE UNITS.............................................................................................................................. 13-7
T
ABLE
: 13–8 MISCELLANEOUS....................................................................................................................................................... 13-8
T
ABLE
: 13–9 USER DEFINABLE OUTPUT FLAGS.......................................................................................................................... 13-8
Table: B–1 REQUIRED SETTINGS FOR MODBUS COMMUNICATIONS........................................................................................B-1
Table: B–2 FAULT REPORT BYTE SEQUENCE...............................................................................................................................B-3
Table: B–3 FAULT REPORT EVENTS SEQUENCE..........................................................................................................................B-4
Table: B–4 MODBUS MEMORY MAP................................................................................................................................................B-5
Table: B–5 DATA FORMATS............................................................................................................................................................B-15
Table: C–1 IMPLEMENTATION TABLE .............................................................................................................................................C-4
Table: C–2 DEFAULT VARIATIONS ..................................................................................................................................................C-5