GHL ProfiLux 4 - Resource Guide Manual

115 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

ProfiLux 4

Resource Guide

Step-by-step resource guide for ProfiLux 4

As of November 2018

Table of Contents

Default Chapter2
- Table of Contents2
Getting Started5
- About this Guide5
- Please Read: Navigating through this Resource Guide5
- Please Read: Profilux 4 Connection Ports Overview6
- To Do: Unpack and Connect All Cables to the P48
- To Do: Change the Langage from German to English9
- To Do: Install Ghl Control Center9
- To Do: Download Ghl Connect App9
Profilux 4 Connectivity Options10
Learning the Basics of Ghl Control Center10
- Gcc Start Screen11
- GCC Tabs: Devices12
- GCC Tabs: View13
- GCC Tabs: Help13
- GCC Tabs: Tools13
- GCC Tabs: Extras14
- GCC Tabs: Backup and Restore14
- GCC Tabs: Communication15
To Do: Connect Via Usb16
To Do: Setup Wi-Fi Connectivity17
- Wi-Fi Auto IP Setup18
- Wi-Fi Static IP Setup19
- RECOMMENDED: Setup P4 Wi-Fi Hotspot Settings21
How to Connect to the P4 Via Wi-Fi22
- Recommended: Connect Via Wi - Fi Using Ghl Control Center23
How to Setup Myghl Cloud Access24
Ghl Control Center Walkthrough27
- Illumination - Light Composer28
- Illumination - Illumination Ch 1-3229
- Illumination - Thunderstorm30
- Illumination - Simulation31
- Illumination - Temp.-Dep.lightred32
- Illumination - Acclimation33
- Processes - Timers34
- Processes - Reminders36
- Dose Overview36
- Dose Overview - Dosing Pump (Part 1)37
- Dose Overview - Dosing Pump (Part 2)39
- Extras - Stream Group40
- Extras - Feed Pause41
- Extras - Maintenance Mode / Power Cut Monitoring41
- Probe/Sensor Controls - Basics42
- Probe/Sensor Controls - Level Settings44
- Probe/Sensor Controls - Measurement Data46
- Display47
- System47
- System - Communication48
- System - Switch Channels and Outlets49
- System - 1-10V Interface50
- Email Notification (Profilux)51
To Do: Assign Pab-Devices to the Profilux 452
To Do: Probe Calibration55
- Probe Calibration Terminology56
- P Hprobe Calibration56
- Redox Probe Calibration57
- Conductivity Probe Calibration58
To Do: Setup Heater Control59
To Do: Setup Return Pump Control62
- React to a Feed Pause63
- Shut down Pump if Sump Water Level Gets too Low63
- Combine Feed Pause and Leakage Detection63
- Interface63
- React to a Maintenance Mode63
To Do: Setup Skimmer Control64
- React to a Feed Pause64
- Turn on Skimmer During Certain Times of the Day (Timer)64
- Shut down Skimmer if Sump Water Level Gets too High or Cup Is Full64
- React to a Maintenance Mode64
- Setting a Skimmer Delay after a Maintenance Mode64
- Combine Feed Pause and Timer Function65
- Combine Feed Pause and Leakage Detection65
To Do: Setup Non-Dimmable Lighting Timers65
- OPTIONAL: Temperature Dependent Light Reduction68
To Do: Setup Normal On/Off Timers69
How to Setup 1-10V Lighting Control71
- OPTIONAL: Temperature Dependent Light Reduction74
How to Setup 1-10V Pump Control76
How to Setup Dosing Pump Schedules80
How to Setup Reminders81
How to Setup Feed Pause Functions82
How to Setup Maintenance Modes85
How to Setup Ato Control (1 or 2 Sensors)86
How to Setup Awc Function90
How to Setup Leakage Detection94
How to Setup Email Notification98
How to Update Profilux 4 Firmware101
How to Update Profilux 4 Wi-Fi Module, Web Server, Web Interface105
How to Update Pab-Device Firmware107
Programmable Logic Examples110
- How to Delay a Skimmer from Turning on after Maintenance Mode Ends110
- Combining Feed Pause and Leakage Detection (Using and Function)112
- Combining Feed Pause and Timer Function (Using or Function)113
- Combining Multiple PL Functions (Using and Function)114
How-To Videos115
Quick Way to Connect to Your P4 Right out of the Box115

Other manuals for GHL ProfiLux 4

Instruction Manual49 pages

Programming Guide81 pages