Hitachi GR2000 Series - Page 36

GR2000 Installation Guide
xxxvi GR2K-GA-1002
Rev. 6.03
4.6.1.1 Routing Capacity of GR2000 on ATM Interface............................................................ 4-58
4.6.1.2 Cellularization Overhead............................................................................................... 4-58
4.6.1.3 Possible Loss of Link with Other Device Due to Shaping............................................. 4-59
4.6.1.4 Outbound QoS on ATM Interface.................................................................................. 4-60
4.6.1.5 Relationship between Load on RP and QoS................................................................. 4-60
4.6.1.6 Setting of VP peak cell rate........................................................................................... 4-60
4.6.2 Required Settings for ATM Connection with Other Device.....................................................4-61
4.6.2.1 ATM Connection with Hitachi NP200 and NP220......................................................... 4-61
4.6.2.2 ATM Connection with Hitachi AN1000..........................................................................4-62
4.6.2.3 ATM Connection with Cisco Systems’ Router............................................................... 4-62
4.6.3 Connection to ATM Services ..................................................................................................4-63
4.6.4 Function-wise Conditions for ATM Connection ......................................................................4-63
4.6.4.1 ATM Connection with IPX Devices ............................................................................... 4-63
4.6.4.2 ATM Connection with Bridge Devices...........................................................................4-63
4.6.4.3 Parallel PVC..................................................................................................................4-63
4.7 Precautions on IP Connection with Other Devices..................................................................... 4-64
4.7.1 Interface Address in Point-to-Point Line Connection..............................................................4-64
4.7.2 Precautions When Using RIP-1 on Frame Relay or ATM Network ........................................4-64
4.7.3 Precautions When Using RIP-2 on Frame Relay or ATM Network ........................................4-64
4.7.4 Precautions When Using OSPF on Frame Relay or ATM Network........................................ 4-64
4.7.5 Cautions When Using RIP-1 in Point-to-Point Circuits........................................................... 4-65
4.7.6 Cautions When Using OSPF on Point-to-Point Circuits ......................................................... 4-65
4.7.7 Cautions When Using OSPF.................................................................................................. 4-65
4.7.7.1 Cautions Regarding the HelloInterval Default Value.....................................................4-65
4.7.7.2 Cautions Regarding the Priority Default Value..............................................................4-65
4.7.8 Cautions When Using BGP-4................................................................................................. 4-66
4.7.8.1 Cautions Regarding NextHop Resolution ..................................................................... 4-66
4.8 Precautions When Replacing Other Router with GR2000.......................................................... 4-67
4.9 Connection with IPv6 Router........................................................................................................ 4-68
4.9.1 Connection with IPv6 Router ..................................................................................................4-68
4.9.1.1 Interface Address of Point-to-Point Type Line ..............................................................4-68
4.9.1.2 Caution on BGP4+ Connection Using Point-to-Point Type Line...................................4-68
4.9.1.3 Caution When Changing the MTU Length of IPv6 Relay Line...................................... 4-69
4.9.1.4 Hardware relaying function in the same link ................................................................. 4-69
4.9.1.5 Destination IPv6 address of Ping6 and traceroute6 commands ...................................4-71
4.9.1.6 IPv6 function that can be used at IPv6 relaying software processing...........................4-71
4.10 Precautions on IPX Connection ................................................................................................. 4-73
4.10.1 Configuration Settings .......................................................................................................... 4-73
4.10.1.1 Setting of RIP Packet Processing ...............................................................................4-73
4.10.1.2 Setting of SAP Packet Processing.............................................................................. 4-73
4.10.1.3 Handling of Non-Data Packets.................................................................................... 4-73
4.10.1.4 Use of NetWare 4.1..................................................................................................... 4-74
4.10.1.5 IPX Connection with ISDN .......................................................................................... 4-74
4.10.1.6 Transmission Interval Settings for Dynamic RIP/SAP Packets on Pertinent Devices. 4-74