Honeywell Galaxy Dimension series - Page 167

Galaxy Dimension Installer Manual
6-93
53 - Program Outputs (cont’d)
Key:
S = Activates when system is set ? = Activation dependant on system programming
P = Activates when system is Part Set X = Activates during Exit Time
U = Unset E = Activates during Entry Time
A = Activated in any condition L = Switches output off if linked to destination output
- = No effect T = Activates if zone resistance is less than value for tamper s/c
O= Activates when zone is omitted or greater than value for tamper o/c
Table 6-21C. Output Activations per Zone
Output Functions Timer-B Walk
Test
Zone
Omit
Warn ing Cu stom
A
Custom
B
Test Reset
RQD
Mask Valid
cd
Fail
Set
Duress Illegal
Code
Max
Tamp
Abort Unset
Zone Function 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
01 Final – UO A – – –S?– –– – – – – –
02 Exit – UO A – – –S?– –– – – – – –
03 Intruder – UO A – – –S?– –– – – – – –
04 24 Hours – UO A – – –S?– –– – – – – –
05 Security – UO A – – –S?– –– – – – – –
06 Dual – UO A – – –S?– –– – – – – –
07 Entry – UO A – – –S?– –– – – – – –
08 Push Set –UOA – –––––––––––
09 Keyswitch –UOA – –––––UX––––U
10 Secure Final –UOA – –––––––––––
11 Part Final –UOA – –––––––––––
12 Part Entry –UOA – –––––––––––
13 PA –UOA – –––––––––––
14 PA Silent –UOA – –––––––––––
15 PA Delay –UOA – –––––––––––
16 PA Delay Silent –UOA – –––––––––––
17 Link ?U?O?? ? ? ????? ? ? – ? ?
18 Spare –––A – – –––––– – ? – –
19 Fire – UO A – – –A?– –– – – – – –
20 Tamper – UO A – – –A?– –– – – – – –
21 Bell Tamper – UO A – – –A?– –– – – – – –
22 Beam Pair –UOA – –––––––––––
23 Battery Low –UOA – –––––––––––
24 Line Fail –UOA – –––––––––––
25 AC Fail –UOA – –––––––––––
26 Log –UOA – –––––––––––
27 Remote Access –UOA – –––––––––––
28 Video – UO A – – –S?– –– – – – – –
29 Video Exit – UO A – – –S?– –– – – – – –
30 Intruder Delay – UO A – – –S?– –– – – – – –
31 Log Delay –UOA – –––––––––––
32 Set Log –UOA – –––––––––––
33 Custom-A ??O?? ? ? ?????? ? – ? ?
34 Custom-B ??O?? ? ???????????
35 Exitguard LLLOL L LLLLLLLL?LL
36 Mask – – – – – – – – SPE – – – – L ? –
37 Urgent – UO A – – –A?– –– – – – – –
38 PA Unset – UO A – – –U?– –– – – – – –
39 Keyswitch Reset –UOA – –––––––––––
40 Bell Fail –––A – –––––––––––
41 Intr Low – UO A – – –S?– –– – – – – –
42 Intr High – UO A – – –S?– –– – – – – –
43 PSU Fault –UOA – –––––––––––
44–46 Not Used –––– – –––––––––––
47 Vibration – UO A – – –A?– –– – – – – –
48 ATM-1 – UO A – – –A?– –– – – – – –
49 ATM-2 – UO A – – –A?– –– – – – – –
50 ATM-3 – UO A – – –A?– –– – – – – –
51 ATM-4 – UO A – – –A?– –– – – – – –
52 Alarm Extend – UO A – – –A?– –– – – – – –