Honeywell SC Series - Page 5

Honeywell Sensing and Control v
SC 2000, SC2001, SC3004
Rev. G, 008-0608-00
Figures
Figure 4-1: External Arrangement of ac powered SC2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 4-2: Panel Cutout Drawing for SC2000 (not to scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 4-3: Internal Arrangement of SC2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 4-4: External Arrangement of AC powered Model SC2001 . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 4-5: External Arrangement of Model SC3004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 5-1: Function Input Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 5-2: Open-Collector Output Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 6-1: Address Jumper Block Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 6-2: Address Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 9-1: Limit Operation when LIMIT.ENERGIZE = SIGNAL > SETPOINT . . . . . . . . . . . . . . . . . . . . . 25
Figure 9-2: Limit Operation when LIMIT.ENERGIZE = SIGNAL < SETPOINT . . . . . . . . . . . . . . . . . . . . . 25
Figure 9-3: Limit Operation when LIMIT.ENERGIZE = SIGNAL INSIDE . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 9-4: Limit Operation when LIMIT.ENERGIZE = SIGNAL OUTSIDE . . . . . . . . . . . . . . . . . . . . . . 25
Figure 10-1: Unamplified Transducer Connection to Strain-Gage Input Channel . . . . . . . . . . . . . . . . . . 27
Figure 10-2: Shunt Calibration Resistor Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 10-3: Digital-to-Analog Output Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 11-2: Digital-to-Analog Output Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 12-1: “Bi-polar Voltage Amp” Connection to High-Level Input Channel . . . . . . . . . . . . . . . . . . . . 49
Figure 12-2: “3-wire Voltage Amp” Connection to High-Level Input Channel . . . . . . . . . . . . . . . . . . . . 50
Figure 12-3: “3-wire Voltage Amp w/Single-Wire Shunt Cal” Connection to High-Level Input Channel . . . . . . . 51
Figure 12-4: “3-wire Current Amp” Connection to High-Level Input Channel . . . . . . . . . . . . . . . . . . . . . 52
Figure 12-5: “2-wire Current Amp w/Buffered Shunt Cal” Connection to High-Level Input Channel . . . . . . . . . 53
Figure 12-6: “2-wire Current Amp w/Single-Wire Shunt Cal” Connection to High-Level Input Channel . . . . . . . 54
Figure 12-7: “Low Voltage” dc-dc LVDT Connection to High-Level Input Channel . . . . . . . . . . . . . . . . . . 55
Figure 12-8: Excitation and Signal Jumper Locations on the High-Level Input Channel . . . . . . . . . . . . . . . 56
Figure 12-9: Digital-to-Analog Output Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 14-1: Digital-to-Analog Output Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68