HP StoreFabric SN6500B

Fabric OS Administrator’s Guide 345
53-1002745-02
Chapter
12
Traffic Isolation Zoning
In this chapter
•Traffic Isolation Zoning overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
•Enhanced TI zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
•Traffic Isolation Zoning over FC routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
•General rules for TI zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
•Supported configurations for Traffic Isolation Zoning. . . . . . . . . . . . . . . . . 358
•Limitations and restrictions of Traffic Isolation Zoning. . . . . . . . . . . . . . . . 359
•Admin Domain considerations for Traffic Isolation Zoning. . . . . . . . . . . . . 360
•Virtual Fabrics considerations for Traffic Isolation Zoning . . . . . . . . . . . . . 361
•Traffic Isolation Zoning over FC routers with Virtual Fabrics . . . . . . . . . . . 363
•Creating a TI zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
•Modifying TI zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
•Changing the state of a TI zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
•Deleting a TI zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
•Displaying TI zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
•Troubleshooting TI zone routing problems. . . . . . . . . . . . . . . . . . . . . . . . . . 370
•Setting up TI over FCR (sample procedure) . . . . . . . . . . . . . . . . . . . . . . . . . 371
Traffic Isolation Zoning overview
The Traffic Isolation Zoning feature allows you to control the flow of interswitch traffic by creating a
dedicated path for traffic flowing from a specific set of source ports (N_Ports). For example, you
might use Traffic Isolation Zoning for the following scenarios:
• To dedicate an ISL to high priority, host-to-target traffic.
• To force high volume, low priority traffic onto a given ISL to limit the effect on the fabric of this
high traffic pattern.
• To ensure that requests and responses of FCIP-based applications such as tape pipelining use
the same VE_Port tunnel across a metaSAN.
Traffic Isolation Zoning does not require a license.
Traffic isolation is implemented using a special zone, called a Traffic Isolation zone (TI zone).
A TI zone indicates the set of N_Ports and E_Ports to be used for a specific traffic flow. When a
TI zone is activated, the fabric attempts to isolate all inter-switch traffic entering from a member
of the zone to only those E_Ports that have been included in the zone. The fabric also attempts to
exclude traffic not in the TI zone from using E_Ports within that TI zone.