HP StoreFabric SN6500B User Manual

Fabric OS Administrator’s Guide 477
53-1002745-02
10G licensing
18
aTFPNFXGLmABANMGtT4LfSBJSDLWTYD3EFrr4WGAEMBA
10 Gigabit FCIP/Fibre Channel (FTR_10G) license
Capacity 1
Consumed 1
Configured Blade Slots 1
8510-8switch:admin> licenseslotcfg -remove FTR_10G 1
8510-8switch:admin> licenseslotcfg -add FTR_10G 4
8510-8switch:admin> licenseshow
aTFPNFXGLmABANMGtT4LfSBJSDLWTYD3EFrr4WGAEMBA
10 Gigabit FCIP/Fibre Channel (FTR_10G) license
Capacity 1
Consumed 1
Configured Blade Slots 4
8510-8switch:admin> portcfgoctetspeedcombo 4/2 2
8510-8switch:admin> portcfgspeed 4/2 10
8510-8switch:admin>
Example of assigning a 10G license on a Brocade 6510 and enabling 10 Gbps operation on a port
This example assigns a license to a Brocade 6510 switch and enables 10 Gbps operation on
port 2.
6510-switch:admin> licenseadd aTFPNFXGLmABANMGtT4LfSBJSDLWTYD3EFrr4WGAEMBA
6510-switch:admin> licenseshow
aTFPNFXGLmABANMGtT4LfSBJSDLWTYD3EFrr4WGAEMBA
10 Gigabit FCIP/Fibre Channel (FTR_10G) license
Capacity 1
Consumed 1
6510-switch:admin> portcfgoctetspeedcombo 2
6510-switch:admin> portcfgspeed 2 10
Enabling the 10-GbE ports on an FX8-24 blade
Use the following procedure to enable the 10-GbE ports on an FX8-24 blade:
1. Connect to the Brocade Backbone and log in using an account with admin permissions, or an
account with OM permissions for the license class of RBAC commands.
2. Use the licenseAdd command to add the 10G license.
3. Use the licenseShow command to check the results of automatic license assignment. If the
results are not what you intended, use the licenseSlotCfg command to reassign the license to
the desired FX8-24 blades.
4. Use the licenseShow command to verify the license.
5. Use the bladeCfgGeMode
--set mode command to configure the GbE port mode for the
FX8-24 blade. To enable the 10-GbE ports, set the mode parameter to one of the following:
• 10g—Enables both 10-GbE ports, disables all ten 1-GbE ports.
• dual—Enables the xge0 port (but not xge1) and also enables all ten 1-GbE ports.
Example of assigning a 10G license on an FX8-24 extension blade and enabling both 10-GbE ports
This example assigns a license to slot 7 on a DCX 8510-4 Backbone and enables both 10-GbE
ports on the FX8-24 blade in that slot. In this example, the license was first automatically assigned
to slot 1.
8510-4switch:admin> licenseadd aTFPNFXGLmABANMGtT4LfSBJSDLWTYD3EFrr4WGAEMBA
8510-4switch:admin> licenseshow

HP StoreFabric SN6500B Specifications

General

Brand	HP
Model	StoreFabric SN6500B
Category	Software
Language	English