Huawei SmartAX MA5600T User Manual

huawei(config)#interface vdsl 0/2
huawei(config-if-vdsl-0/2)#display port state 4
------------------------------------------------------------------------------
Port Status Loopback Line Template Alarm Template Bonding-group
------------------------------------------------------------------------------
4 Activated Disable 10 1 -
------------------------------------------------------------------------------
The query result shows that line template 10 is bound to port 4. Run the display vdsl line-
template command to query the channel profile and line profile in the line template.
huawei(config-if-vdsl-0/2)#display vdsl line-template 10
------------------------------------------------------------------------------
Template index: 10 Name: VDSL LINE TEMPLATE 10
Line profile index : 1
Channel1 profile index : 10
Channel1 rate adaptation ratio downstream : 100
Channel1 rate adaptation ratio upstream : 100
------------------------------------------------------------------------------
Step 2 Confirm whether to change the transmission mode and signal noise ratio (SNR).
The query result shows that line profile 1 and channel profile 10 are in line template 10. Run the
display vdsl line-profile command to query the transmission mode and SNR configured in the
line profile.
huawei(config-if-vdsl-0/2)#display vdsl line-profile
1
------------------------------------------------------------------------------
Profile index: 1 Name: DEFVAL
Transmission mode:
T1.413 G.992.1(Annex A/B/C)
G.992.2(Annex A/C) G.992.3(Annex A/B/I/J/L/M)
G.992.4(Annex A/I) G.992.5(Annex A/B/I/J/M)
G.993.2(Annex A/B/C)
Bit swap downstream : Enable
Bit swap upstream : Enable
Form of transmit rate adaptation downstream : AdaptAtStartup
Form of transmit rate adaptation upstream : AdaptAtStartup
Target SNR margin downstream(0.1dB) : 60
Minimum SNR margin downstream(0.1dB) : 0
Maximum SNR margin downstream(0.1dB) : 300
Target SNR margin upstream(0.1dB) : 60
Minimum SNR margin upstream(0.1dB) : 0
Maximum SNR margin upstream(0.1dB) : 300
UPBO US1 band reference PSD parameters[a, b] : 1650,1020
UPBO US2 band reference PSD parameters[a, b] : 1650,615
UPBO US3 band reference PSD parameters[a, b] : 0,0
UPBO US4 band reference PSD parameters[a, b] : 0,0
---- More ( Press 'Q' to break ) ----
l If the transmission mode is ADSL, change the transmission mode to VDSL or ALL. To do
so, proceed to Step 3.
l If the SNR value does not meet actual requirements over the live network, change it according
to actual conditions. To do so, proceed to Step 3.
l If the transmission mode is VDSL or ALL and the SNR value also meets actual conditions
over the live network, go to Step 4.
Step 3 Run the vdsl line-profile quickadd command to reconfigure the transmission mode and SNR.
In addition, configure exclusive VDSL parameters.
1. According to actual conditions over the live network, SNR is planned to 7 dB, transmission
mode to all (its value is 1), and line profile index to 11.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
3 Configuring the DSLAM Services
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
289

Huawei SmartAX MA5600T Specifications

General

Brand	Huawei
Model	SmartAX MA5600T
Category	Control Unit
Language	English