IBM 6C1 - Multiboot

377 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Multiboot

The options available from this screen allow you to view and set

various options regarding the operating system and boot devices.

Software

Default

Install

From

Select

Software

Boot

Sequence

Multiboot Startup

EXIT

Chapter 8. Using System Management Services 221

Table of Contents

Default Chapter5
- Table of Contents5
- Rack Safety Instructions11
Safety Notices11
- Electrical Safety12
- Laser Safety Information13
  - Laser Compliance13
Data Integrity and Verification15
About this Book17
- Iso 900017
- Related Publications17
- Trademarks18
Chapter 1. Reference Information19
- System Unit Locations19
- System Logic Flow Diagram31
- Location Codes32
- AIX and Physical Location Code Table36
- System Cables40
- Specifications41
- Power Cables43
- Service Inspection Guide44
Chapter 2. Diagnostic Overview45
- Maintenance Analysis Procedures (Maps)45
- Attention LED and Lightpath Leds46
- Checkpoints48
- FRU Isolation49
- Electronic Service Agent for the RS/600049
- Using the Service Processor and Electronic Service Agent Features49
  - Service Processor49
  - Electronic Service Agent50
Chapter 3. Maintenance Analysis Procedures (Maps)53
- Quick Entry MAP54
  - Quick Entry MAP Table of Contents54
- MAP 1020: Problem Determination62
- MAP 1240: Memory Problem Resolution67
  - General Memory Information68
- MAP 1520: Power71
- MAP 1540: Minimum Configuration81
Chapter 4. Checkpoints103
- Unresolved Checkpoint Problems103
- Service Processor Checkpoints104
- Firmware Checkpoints110
- Boot Problems/Concerns128
Chapter 5. Error Code to FRU Index133
- Performing Slow Boot133
- Considerations for Using the Error Code to FRU Index133
- Firmware/Post Error Codes134
- Memory DIMM Present Detect Bits (PD-Bits)194
- Error Codes E0A0, E0B0, E0C0, E0E0, E0E1 and 40A00000 Recovery Procedure195
- Bus SRN to FRU Reference Table196
- Typical Boot Sequence for Eserver Pseries 610 Model 6C1 and Model 6E1197
Chapter 6. Loading the System Diagnostics199
- Performing Slow Boot199
- Loading Standalone Diagnostics199
- Loading Online Diagnostics199
- Default Boot List and Service Mode Boot List200
Chapter 7. Using the Service Processor201
- Service Processor Menus202
- General User Menu203
- Privileged User Menus205
- System Power-On Methods224
- Service Processor Call-In Security225
- Service Processor Reboot/Restart Recovery225
- Service Processor System Monitoring - Surveillance227
- Console Mirroring229
  - System Configuration for Console Mirroring229
- Service Processor Firmware Updates230
- Service Processor Error Log230
- Service Processor Operational Phases231
- Service Processor Procedures in Service Mode233
Chapter 8. Using System Management Services235
- Graphical System Management Services235
  - System Management Services236
- Config238
- Multiboot239
- Utilities242
- Firmware Update256
  - Firmware Recovery256
- Text-Based System Management Services257
- Select Language258
- Change Password Options259
  - Set Privileged-Access Password259
  - Unattended Start Mode259
- View Error Log260
- Setup Remote IPL (Initial Program Load)261
- Change SCSI Settings264
- Select Console264
- Select Boot Options265
  - Select Boot Device267
  - Configure Nth Boot Device268
- View System Configuration Components269
- System/Service Processor Firmware Update270
- Firmware Recovery270
Chapter 9. Removal and Replacement Procedures271
- Handling Static-Sensitive Devices272
- Stopping the System272
- Placing the Model 6C1 in the Service Position273
- Front Door (Model 6E1)274
- Removal274
  - Replacement275
- Covers276
  - Service Access Cover (Model 6E1)276
  - Service Access Cover (Model 6C1)278
- Bezels280
  - Model 6E1280
  - Model 6C1281
- Processor and Memory Card Cover282
  - Removal282
  - Replacement282
- CEC Cage283
  - Removal283
  - Replacement283
- Memory Card and Memory Dimms284
  - Memory Card Removal284
  - Memory Card Replacement289
- Processor Card291
  - Removal291
  - Replacement292
- Adapters294
  - Removal294
  - Replacement295
- System Board298
  - Removal298
  - Replacement299
- Power Supply300
  - Removal300
  - Replacement302
- Operator Panel305
  - Removal305
  - Replacement305
  - System Vital Product Data (VPD) Update Procedure306
- Power Backplane308
  - Removal308
  - Replacement308
- SCSI Backplane309
  - Removal309
  - Replacement310
- Media Devices (CD-ROM, Tape, or Disk Drive)311
  - Removal311
  - Replacement312
- Battery313
  - Removal313
  - Replacement314
- Hot-Swap Disk Drives315
  - Deconfiguring (Removing) or Configuring a Disk Drive315
  - Deconfiguring (Removing)315
  - Configuring (Replacing)316
  - Removal317
  - Replacement318
- Hot-Swap Fan Assembly319
  - Removal319
  - Replacement320
Chapter 10. Parts Information321
- System Parts322
- System Internal Cables326
- SCSI Cables328
- Keyboards and Mouse (White)332
- Keyboards and Mouse (Black)333
Appendix A. Environmental Notices335
- Product Recycling and Disposal335
- Environmental Design335
- Acoustical Noise Emissions336
  - Declared Acoustical Noise Emissions336
Appendix B. Notices337
Appendix C. Service Processor Setup and Test339
- Service Processor Setup Checklist339
- Testing the Setup340
Appendix D. Modem Configurations343
- Sample Modem Configuration Files343
  - Generic Modem Configuration Files343
  - Specific Modem Configuration Files343
- Configuration File Selection344
- Transfer of a Modem Session349
  - Recovery Strategy350
  - Prevention Strategy350
- Modem Configuration Sample Files351
Appendix E. Firmware Updates367
- Checking the Current Firmware Levels367
- Updating System Firmware367
Index369

Related product manuals

IBM pSeries 630 6C4

IBM RS/6000 H50

IBM SC34-6814-04

IBM S85 pSeries 680

Preview: IBM RS/60000 Series

IBM RS/60000 Series

IBM RS/6000 7014-S00

IBM RS/6000 7043 260

IBM RS/6000 7044 Model 170

IBM RS/6000 7025 F50 Series

7026-H80 - RS/6000 - 256 MB RAM