54 Programming the telephone
Centrali anti-intrusione
11-2-1
Telephone line adjustment
The “Outgoing voice volume” and “Incoming voice volume” parameters can be used to correct
the voice functions of the dialer and DTMF tones (refer to
Table 4-3: Control panel options
).
The values of these parameters affect each other, therefore, and a good result is always a
compromise.
If you are not using a GSM interface, you should:
• Adjust one parameter at a time and carry out tests to verify the result.
• Increase/decrease the values in small steps (for example, from 25 to 22 and not from 25
to 15).
Number of rings
for answerphone
This value determines the number of rings the system
allows before picking up an incoming call (from 1 to
15).
Telephone
Number of rings
Ring sensitivity
This value determines the reception sensitivity of
incoming call rings.
At default this value is set at 60. Accepted values: 1 to
120.
Other parameters,
Ring sensitivity
Call all voice/
digital/SIA-IP
numbers
If several voice calls (digital or SIA-IP) generated by
the an event are waiting in the outgoing call queue,
the control panel will attempt to send voice calls to all
the numbers of this type.
Telephone
parameters,
Telephone dialer
parameters
Parameters
Call allVoxNums
Call all TLVNums
Call all SIA-IP
Access DTMF
menu without
code
Allows access to the User Menu over-the-phone
(during voice calls from the control panel) in
accordance with the access level (enabled options,
etc.) of the last user code that operated on the control
panel (code 30, 50 or 100).
DTMF withoutCode
Start message
after dialing
The control panel will start the voice message 5
seconds after dialing the respective contact number.
BypassVoiceCheck
Confirm call with
“*”
The control panel will consider the voice call successful
when the recipient presses the “*” key on the
telephone keypad.
Confirm with *
UTC Time on
SIA-IP
Calls to SIA-IP type numbers will contain the date and
time in “UTC” format (Coordinated Universal Time).
UTC timeOnSIA-IP
Increase DTMF
sensitivity
Option that increase the sensitivity of incoming DTMF
tones.
DTMF sensitivity
No SIA strings
No SIA-IP
strings
The descriptive strings will not be sent in SIA/SIA-IP
protocol.
NoStrings SiaProt
NoStrings SIA-IP
Arm/Disarm
inverted on C.ID
Partition arming events using CONTACT-ID protocol
will send the "New event/Event activation" code when
the partition arms, and the "Event ended/Event
restore" code when the partition disarms.
CONT-IDInversion
Generates one
call only for each
event
If this option is enabled, it blocks all the calls
programmed for an event after the first successful
call. If the options “Call all voice/digital/SIA-IP
numbers” are enables, then the latter have priority.
SingleCallEachEv
Stop calls on dis-
arm with no
alarms
The control panel will not carry out the calls
programmed for disarm events when there is no active
alarm or alarm memory present.
Disab.Tel.Disarm
Number of voice
mess. repeti-
tions
This value determines the number of times the voice
message will be played during the call (from 1 to 15).
Telephone
Message repeats
Number of
attempts
This value determines the number of calls attempts
the system will make before deleting the contact
number from the call queue (from 1 to 15).
Max.num.attempts
Delay on line-
down signal
This parameter allows you to program the delay,
expressed in seconds or minutes, which will be applied
before “Line Down” events is signalled.
Other parameters,
LinedownDelay
Telephone num-
ber 15 reserved
for teleservice
For future use
Telephone
parameters,
Teleservice
parameters
Parameters
Num15 ForTeleserv
Installer call-
back
For future use
Install.callback
SIA-IP polling
interval
Programming field for the setting, expressed in
seconds, of the between two consecutive polling
signals.
Telephone
parameters
Not available
Disabled
Option that disables the polling function for all
telephone numbers.
Table 11-2: Telephone parameters
To Next Page
Loading...