Programming manual
Programming events 57
12-1
Programming single events
Note
The “Force call to alternative channel” option is valid only for the Nexus that is installed.
OUTPUT
For the conditions of Zone alarm, Terminal tamper, Partition alarm, Partition in Stay-mode
alarm and Partition tamper, if a monostable output is programmed in the "Outputs" parameter,
Table 12-1: Single event parameters
Parameter Software section Installer menu section
Activation /
Restoral
The actions are arranged on lines in a table, each with
a check box for the activation of the action when the
event occurs and a check box for the activation of the
action when the event restoral.
Events list,
selected event,
Actions
Events, "Event type",
"event", Activation/
Restoral
Tel. number “x”
This section allows you to select the telephone
numbers to call on event activation/restoral.
TelephoneNumbers
Output
The output to be activated on activation/restoral of
each event can be selected from the check-box list.
Outputs
Notification to
Cloud
If the panel is registered with the Cloud, the event will
be sent to the Cloud.
Not available
Activate peri-
odic event
When the event occurs, the system will generate
Periodic event number 1.
Options
StartPeriodicEv.
Clear call queue
When the event occurs, the system will cancel the
outgoing call queue.
Clear call queue
Memory
If this option is enabled, activation/restoral of the
event will be saved to the events log.
Event ON to log/Event
OFF to log
Voice message
on keyp. 001
Activation of message playback on the keypad must
be set on the keypad at address “001” on activation/
restoral of the selected event.
Local Message ON
(for activation)
Local MessageOFF
(for restoral)
Output scenarios
This section provides boxes for the selection of one of
the 50 output scenarios, a field for event activation
and one for event restoral.
Not available
Shortcut on
event
This programming field is for the selection of a control
panel operation that will be activated automatically
when the event occurs (refer to paragraph 12-1-2
Shortcut on event).
This field is followed by a further two fields for the
definition of the respective parameters.
Events list,
selected event
Not available
Sounder/flasher
pattern
If a sounder/flasher is included in the outputs, its
activation will occur in accordance with the selected
pattern.
Siren sound types
Silent event
If the event occurs, the system will generate silent
calls which will not be signalled on the keypads.
Options
Silent event
Force call to
alternative chan-
nel
Calls associated with this type of event will be made
via the alternative channel of the channel
programmed for each telephone number (see
Channel on Table 11-1: Parameters of single
telephone number).
ForceAlt.Channel
Priority event
Calls associated with this type of event have priority
over all other calls. Therefore, if a priority event
occurs, any ongoing calls will be interrupted and the
priority-event call will be sent immediately.
Priority
Enable SMS
mess.
When the event occurs, the control panel will send an
SMS message to all the duly enabled telephone
numbers (refer to Table 11-1: Parameters of single
telephone number, “Receive SMS” parameter.
Events list,
selected event
Nexus
Enable SMS
Automatic SMS
If enabled, the dispatched SMS message will consist of
the event description contained in the Events log.
Automatic SMS
SMS number
If the “Automatic SMS” option is not activated, the
SMS message, selected from the 50 available on the
Nexus, will be sent (refer to paragraph 3-5-3 SMS
message texts).
Not available
Other outputs
This section allows you to activate additional outputs
(besides the one programmed for the “Outputs”
parameter) in connection with the verification or
restoral of the event.
Events list,
selected event,
Other outputs
Events, "Event type",
"event", Activation/
Restoral
Other outputs
Configure object
At the bottom of the section is a button that accesses
directly the programming section of the object
(system component) associated with the selected
event.
To Next Page
Loading...