112 Technical terminology and Glossary
Anti-intrusion control panels
A group of operating parameters set at the factory by the manufacturer. The purpose of these
settings is to reduce the work of the installer during the installation phase.
The installer can restore the system to “Default Settings” if necessary.
DEFAULT SETTINGS
Violation of a zone with this configuration will not generate an alarm but will trigger the associated
Timer (Entry time). If the user does not disarm the partition/s within the set “Entry time”, the
system will generate an alarm.
For example, the zone that monitors the main door of a building is usually configured as a
Delayed Entry Zone, in order to give building occupants time to enter the building and disarm the
partition without generating an alarm.
DELAYED ENTRY ZONE
Violation of a zone with this configuration will not generate an alarm but will trigger the associated
Timer (refer to Exit time).
For example, the zone that monitors the main door of a residence or building is usually configured
as a delayed exit zone, in order to give occupants time to leave the partition after an arming
operation. If the user does not leave the zone within the set “Exit time”, the system will generate
an alarm.
DELAYED EXIT ZONE
This is an explicit user-command which ends signalling on the red and yellow LEDs on keypad and
readers for the following events:
•Zone Alarm
• terminal tamper
• open panel or dislodged panel
• peripheral tamper (keypads, expansions, readers)
• peripheral loss (keypads, expansions, readers)
•false key
• ongoing fault
•memory fault
If a user deletes the alarm/tamper memory, the visual signals on the reader/keypad LEDs will
clear.
If the settings for norm. 50131 compliancy are active, the keypads may, in addition, require entry
of a level 3 access code code (installer code) for the deletion of fault memories.
DELETE ALARM/
TAMPER/FAULT
MEMORY
This device allows the control panel to send report calls to Alarm Receiving centres (ARC).
SmartLiving control panels provide a built-in digital dialler which supports all the most widely used
protocols.
DIGITAL DIALER
An electrical input point used for the management/supervision of signals coming from 2 intrusion
detection devices.
The terminal the zone is connected to must be configured as a “double input zone". Terminals with
this configuration allow the system to distinguish between two distinct alarms coming from the
two different zones it is connected to.
DOUBLE ZONE
The time (expressed in minutes or seconds) that the system allows the user to disarm the
partition after zone violation. It the system is not disarmed within the set time it will generate an
alarm.
Each partition can be programmed with its own Entry time.
ENTRY TIME
(OR ENTRY DELAY)
An operative status recognized by the system.
For example: detector alarm, mains failure (230V
~), blown fuse, user-code recognition, etc., are
all events recognized by the control panel.
Each event is associated with an activation event (when the event occurs) and a restoral event
(when the event ends).
Each event can be programmed to generate the following actions:
• activation of one or more outputs
• activation of an output scenario
• transmission of one or more e-mails
• send one or more SMS messages
• activation of one or more voice calls
• activation of one or more digital calls
• activation of shortcut functions
EVENT
This is the non-volatile portion of the memory the panels saves events to. The events are saved in
chronological order with the following details:
• event description - with details regarding new events and restorals
• information regarding the user or the cause of event
•event location
• event date and time
The events log can be viewed by the system users and the installer.
Partition events (zone alarms, partition alarms, arm/disarm operations, recognized codes and
keys, etc.) can be viewed by users with at least one partition in common with the event element.
For example, if a user arms several partitions from a keypad, the events log will show:
• description of the event - “Arm request”
• description of the code and partitions involved
• description (label) of the keypad involved
• date and time of the request
EVENTS LOG
(OR EVENTS MEMORY)
A short period (expressed in minutes or seconds) during which the user must disarm the partition
after violation (for example, after opening the front door) otherwise the system will generate an
alarm.
Each partition can be programmed with its own Exit time.
EXIT TIME
(OR EXIT DELAY)
These boards can be used to increase the number of terminals (zones or outputs) and/or the size
of the system (in order to extend it over a larger area). Expansion boards can be connected to the
system via the I-BUS.
EXPANSION BOARDS
To Next Page
Loading...
