Installation and programming manual
Options and programming methods 91
7-20
Keypads
This section in the installer menu allows you to program the parameters of the keypads.
Not all the keypad parameters can be accessed via the installer menu. Depending on
the type of keypad or programming process, it may be necessary to use the
SmartLeague software program or, in the case of Alien keypads, access the appropriate
section of the keypad functions.
Via Keypad
Type-in Code
(Installer PIN)
, PROGRAMMING Keypads .
Enable/disable
This section allows you to add/remove expansions from the I-BUS configuration, by
means of keys and .
ChoosePeripheral
This section allows you to program the various options of the selected keypad.
• Wireless - This section allows you to start the enrolling process of the wireless
keypad (future use)
• Temp. hysteresis. - this parameter allows you to enter the hysteresis value for the
“Air conditioning” function on the selected keypad (if enabled).
The entered value must be expressed in °C decimals (from a minimum of 0 to a
maximum of 4).
• Description - editable field for the name of the digital key user.
• Partitions - use and to enable/disable the keypad on the system
partitions.
• Options:
•• Temperature off - if this option is enabled, the room temperature will be flashed
in alternation on the display. This option is valid for keypads with built-in
temperature sensors only.
••
SilentExitTime
- enables/disables the buzzer during partition Exit Time.
••
SilentEntryTime
- enables/disables the buzzer during partition Entry time
•• SignalExitTime - enables/disables the buzzer when terminal T1 on the keypad is
activated as an output.
•• Disable bell - enable/disable the buzzer that signals violation of the bell zone
relative to the keypad in question.
•• LED Off in standby - if enabled, this option switches of the relative LEDS after
at least 40 seconds of inactivity on the keypad.
•• NO Superv. WLS - If enabled, this option inhibits fault signalling in the event of
loss of wireless devices.
This option is co-related to the control panel parameter “Wireless Superv.” (refer
to paragraph 7-27 Other parameters).
•• Disable tamp. WLS - If this option is disabled, open/dislodgement tamper on
Air2 devices will not generate the respective events.
• F1/4KeyShortcuts - setting of the shortcuts assigned to keys , ..., .
If you are programming an Alien keypad, this shortcut refers to the position in the
list available in the “Scenarios” section of the Alien keypad you are working on.
Function keys F1 to F12 must be selected separately and programmed as follows:
•• Type - this is the shortcut action which can be selected from those available
(refer to Appendix B, Shortcuts at default). It is necessary to programme an
extra parameter for some shortcuts:
- “Arm/disarm”, this parameter refers to one of the 30 scenarios
- “Activate outputs”, this parameter refers to the output that will be deactivated
- “Deactiv. outputs”, this parameter refers to the output that will be deactivated
Note
The “Listen-in” and “Arming status” will have no effect if the respective command is entered at a
keypad.
If you are programming an Alien keypad, the only type of shortcut that functions is “Arm/disarm”.
•• Options - activated by means of keys and , are:
- Requires code - if enabled, the system will ask for user-code entry before
activating the shortcut. If the system recognizes the entered user code, it will
activate the shortcut command.
- SecurityRiskCode - if you enable this option, you must also enable the
“Requires code” option. When this option is enabled and the selected
shortcut involves a scenario that completely disarms a partition, or switches
a partition from Away mode to Stay mode, the security of your system will
obviously be at risk, therefore, the system will request code entry.
PROG. KEYPADS
KEYP. 001
KEYP. 002 W
KEYP. 003
Keypads
Enable/disable
ChoosePeripheral
PROGRAMMING
Shortcuts
Expansions
Keypads
Keypads
Enable/disable
ChoosePeripheral
To Next Page
Loading...
