Name: Juniper EX3300
Brand: Juniper
Rating: 4 (1 reviews)

To Next Page

To Previous Page

Table 48: show interfaces ge- Output Fields (continued)

Level of OutputField DescriptionField Name

All levelsName of the logical interface.Logical interface

detail extensive noneIndex number of the logical interface, which reflects its initialization sequence.Index

detail extensive noneSNMP interface index number for the logical interface.SNMP ifIndex

detail extensiveUnique number for use by Juniper Networks technical support only.Generation

All levelsInformation about the logical interface.Flags

All levelsEncapsulation on the logical interface.Encapsulation

detail extensive noneProtocol family.Protocol

detail extensiveNumber and rate of bytes and packets received (input) and transmitted (output)

on the specified interface.

NOTE: For logical interfaces on EX Series switches, the traffic statistics fields

in show interfaces commands show only control traffic; the traffic statistics do

not include data traffic.

Traffic statistics

extensiveEX Series switches do not support the collection and reporting of IPv6 transit

statistics.

IPv6 transit

statistics

extensiveNumber and rate of bytes and packets destined to and from the switch.Local statistics

extensiveNumber and rate of bytes and packets transiting the switch.Transit statistics

detail extensiveUnique number for use by Juniper Networks technical support only.Generation

detail extensive noneRoute table in which the logical interface address is located. For example, 0

refers to the routing table inet.0.

Route Table

detail extensiveNames of any input filters applied to this interface.Input Filters

detail extensiveNames of any output filters applied to this interface.Output Filters

detail extensiveInformation about protocol family flags.

If unicast reverse-path forwarding (RPF) is explicitly configured on the specified

interface, the uRPF flag is displayed. If unicast RPF was configured on a different

interface (and therefore is enabled on all switch interfaces) but was not explicitly

configured on the specified interface, the uRPF flag is not displayed even though

unicast RPF is enabled.

Flags

briefProtocol family configured on the logical interface. If the protocol is inet, the IP

address of the interface is also displayed.

protocol-family

detail extensive noneInformation about the address flags.Flags

Network Interfaces for EX4300 Switches

Juniper EX3300 Specifications

General

Ethernet LAN	Yes
Authentication method	RADIUS, TACACS+
Connectivity technology	Wired
Ethernet interface type	Gigabit Ethernet
Number of VLANs	4096
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3x, IEEE 802.3z
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Copper ethernet cabling technology	1000BASE-T, 100BASE-TX, 10BASE-T
Console port	-
ExpressCard slot	No
Fiber ports quantity	4
USB 2.0 ports quantity	0
Basic switching RJ-45 Ethernet ports quantity	48
Throughput	130 Mpps
Number of queues	8
MAC address table	16000 entries
Maximum data transfer rate	176 Gbit/s
Supported data transfer rates	10, 100, 1000Mbps
Switch type	Managed
Switch layer	L2
Security algorithms	SSH-2
Power source	AC
AC input voltage	100 - 240 V
Power consumption (typical)	100 W
Form factor	1U
Product color	Black
Flash memory	1024 MB
Processor frequency	1000 MHz
Compatible operating systems	Junos
Operating altitude	0 - 3049 m
Non-operating altitude	0 - 4877 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 85 %
Supported network protocols	IPv6