Keysight 34972A - Page 347

Keysight 34970A/34972A User’s Guide 347
enable/disable,, 170
text message,
, 170
fuse
factory setting,, 48
location,
, 15, 16, 48
part number,
, 48
replacing,
, 48
fuseholder assembly,
, 15, 16,
48
G
gage factor (strain),, 301
gain "M" (Mx+B) scaling,
, 59,
144
gate signal (totalizer),
, 160, 326
gauge, wire size,
, 260
GET (Group Execute
Trigger),, 109
GPIB (IEEE-488)
address selection,, 15, 66,
68, 186
cable,
, 73
connector,
, 15
factory address
setting,
, 177, 183, 185, 190
interface selection,
, 66, 68,
186
setting address,
, 177, 183,
185, 190
ground loops,
, 262, 265
grounding,
, 262
H
handle
adjusting,
, 50
handshake (RS-232)
DTR/DSR mode,, 188
factory setting,
, 67, 188
Modem mode,
, 189
None (no flow mode),
, 188
RTS/CTS mode,
, 188
selecting,
, 67, 188
XON/XOFF mode,
, 188
hardware output lines
(alarms),, 153
hardware, rack mounting,
, 52
high-frequency switching,, 319
I
ice bath,, 273
IEEE-488 (GPIB)
address selection,, 66, 68,
186
cable,
, 73
connector,
, 15
factory address
setting,, 185, 190, 191, 192
interface selection,
, 66, 68,
186
setting address,
, 185, 190,
191, 192
impedance mismatching,
, 320
INITiate command
description,, 105
injected current, dc
voltage,, 283
input resistance
dc loading errors,
, 284
dc voltage,
, 138, 139, 284
INPut:IMP:AUTO
command,
, 139
insertion loss,
, 320
installing
BenchLink Data Logger
software,
, 36
Instrument configuration,
importing
, 184
instrument preset state,
, 201
instrument state storage
definition,
, 70
front-panel operation,
, 167
naming states,
, 70, 166
power-down recall,
, 166
remote operation,
, 167
integral error (DAC),
, 328
integrating ADC,
, 87
integration time
definition,, 129
selecting,
, 129
vs. channel delays,
, 116
vs. number of bits,
, 129
vs. number of digits,
, 129
vs. resolution,
, 129
Interface key,, 56, 66, 68, 186
interface, GPIB (IEEE-488)
address selection,
, 66, 68,
186
cable,
, 73
connector,
, 15
factory address setting,
, 185
interface selection,
, 66, 68,
186
setting address,
, 185
interface, RS-232 (serial)
baud rate,
, 67
cable,
, 73
flow control,
, 67
parity,
, 67
stop bits,
, 67
internal DMM
block diagram,
, 268
enabling/disabling,
, 171
reading relay count,
, 173
internal reference
(thermocouple),, 133
internal timer, scan
interval,
, 133
Interval key,
, 55, 107, 123
interval scan
default value,
, 107
resolution,
, 107
setting from front
panel,
, 107
setting from remote,
, 107
settings,
, 107
interval, scan-to-scan,
, 58, 106
IP address
, 191
IPTS-68 conversions,
, 135, 271
isothermal block,
, 133, 275
ITS-90 conversions,
, 135, 271
J
jumper, Totalize Threshold,, 160
junction temperature,
, 272
K
kelvins, setting units,, 132