Kinoton FP 75 E - Important Hints for Installation

81 pages

Save Page as PDF

To Next Page

To Previous Page



Installation / Mounting

Issue: 08/2012



 



Main Page

Table of Contents5
Safety11
Safety Notes11
General Hints11
Dangers When Working with the Projector11
Intended Purpose12
Guarantee and Liability12
Explanations of Symbols and Notes12
Special Hazard Points13
Electric Power Hazards13
Warning Risk of Fire14
Lamphouse Hazards14
1 .3 .3 .1 Broken Glass14
1 .3 .3 .2 Ultraviolet Radiation14
1 .3 .3 .3 High Voltage14
Mechanical Danger15
Preventing Projector Damage15
Service16
Protective Devices17
Main Switch17
IR Reflex Film Break Sensor17
Film Stripper17
Water Flow Control18
Door Switches18
Transportation and Installation / Mounting19
Transportation19
Delivery or Equipment Variations19
Installation20
Place of Installation, Place of Operation20
Important Hints for Installation21
Additional Installation Hints22
Installing and Connecting the Lamphouse Components22
Projector Terminal Strips23
Connecting the Water Cooling (Option)24
Connecting the Non-Rewind System to the Projector24
Function and Components25
Components Overview26
Housing27
Projection Components27
Film Gate and Film Track28
Film Pressure Skate28
The Dowser29
Single Aperture Plates29
Lens Holder30
3 .2 .4 .1 Manual Focusing on the Lens Holder30
Electronically Controlled Lens Holder Focusing (Option)30
Opposed Rotating Double Shutter31
Combined Intermittent Sprocket32
3 .2 .6 .1 Framing32
Constant Speed Sprockets32
Changing the Film Gate and Sprocket Parts (35 MM / 70 MM)34
Sound Devices35
Reverse-Scan Sound Device (Analog and Optional DOLBY Digital / Upgradeable)35
3 .3 .1 .1 Components35
Sound Tracks on the Films (35 MM)36
Magnetic Sound Device (70 MM Film)36
DTS/SDDS Reader36
Drive Components37
Main Drive37
Intermittent Sprocket Drive38
Electronically Controlled Friction Drives38
3 .4 .3 .1 Friction Control38
3 .4 .3 .2 Reel Shaft on Change Flange38
Shutter Drive39
Electronic Components40
Components in the Projector Door40
Components on the Basic Unit41
Shutter Drive Frequency Inverter41
LED Board for Reverse-Scan Sound Device42
Automation Systems42
Operating Elements43
Main Switch43
Operating Panel43
Friction Control44
Remote Control Panels (Option)45
Projection Room Control Panel45
Auditorium Panel46
Operation and Troubleshooting47
Switch on and Start Projector / Stop and Switch off Projector47
Threading for Projection Operation48
Different Projection Speeds50
General Keys50
Projection / Forward Running at 24 Fps or 25 Fps51
Reverse Running (Option with Reverse Running Unit)51
Projecting at VARIA Speed (Option)51
Change-Over Operation52
Changing the Film Format52
Troubleshooting53
General Hints53
Projector Troubleshooting Chart (Type 1 Errors)53
Projector Troubleshooting Chart (Type 2 Errors)53
Analog Sound55
Digital Sound55
Error Indication with Leds56
Interface Board56
Intermittent Sprocket Power Supply Unit56
Main Board57
Cleaning / Maintenance / Repair59
General Hints59
Cleaning59
Maintenance60
Repair61
Changing the Pilot Lamp61
Changing a Constant Speed Sprocket62
Adjusting the Distance between Pad Shoe and Sprocket62
Adjusting the IR Reflex Film Break Sensor63
Adjusting the Film Pressure Skate63
6 .4 .5 .1 Checking and Adjusting the Skate Lifting63
6 .4 .5 .2 Checking and Adjusting the Film Pressure Skate Height64
6 .4 .5 .3 Adjusting the Pressure of the Skate65
Adjusting the Lens Holder66
Parts and Wearing Parts67
Film Gate Parts (35 MM / 70 MM)67
Feed/Bottom Sprockets (35 MM / 70 MM)67
Guide Rollers and Pendulum Rollers (35 MM / 70 MM)67
Other Parts67
Film Spools70
Interchangeable Flanges with Shafts70
Technical Data, Circuit Diagrams and Plans of Terminal Connections71
Technical Data71
Projector71
Reverse-Scan Sound Device72
Magnetic Sound Device Data72
Plans of Terminal Connections73
Plan of X1 Main Terminal Connections73
Plan of X2 Terminal Strip for Projector Functions (Optional)74
Plan of X3 Terminal Strip for Auditorium Functions (Option)75
BWR Control Panel on Terminal Strips X2 + X375
35 MM Sound Output on 8-Pole Terminal Strip76
Block and Circuit Diagrams77
Block Diagram (Components Overview)77
Main Board Components Overview78
Lamphouse for 230 V Mains Connection79
Lamphouse for 120 V Mains Connection80

Kinoton FP 75 E - Important Hints for Installation

Table of Contents

Related product manuals