Kurzweil PC3LE - The Soft Buttons in Program Mode; Saving Controller Settings

Program Mode
The Program Mode Page
6-3
Enterbutton.Ifyouusethismethod,makesuretounlightthecategoryshiftbuttonbypressing
itagainaftermakingyourselection.)Lastly,holdthecategorybuttonthatyouwishtosavea
favoriteforforafewseconds.Thenexttimeyouchoosethatcategory,yourfavoritewillbe

selected.
Startup Program
Youcansavethecurrentsettingsforprogrammode(selectedchannel,selectedprogramoneach
channel)byenteringandthenexitingmastermode.Thissavesamastertable(seeChapter 9,
MasterModefordetails.)Bydoingthis,yourselect edchannelandprogramwillloadthenext
timeyoupower
onthePC3LE.
The Soft Buttons in Program Mode
UsetheOctav–andOctav+softbuttonstotransposeupordownbyafulloctave.Pressingboth
Octavbuttonssimultaneouslyreturnsthetranspositiontoitsoriginalsetting.
PressingthePanicsoftbuttonsendsanAllNotes OffmessageandanAllControllersOff
messageonall16MIDIchannels.
Pressthe
Infosoftbuttontoseeallofthecontrollerassignmentsofthecurrentprogram.Scroll
downthepageusingtheAlphaWheelorthe‐/+buttons.Infotextisautomaticallycreatedwhen
assigningacontrollertoaparameterwithintheProgramEditor(seeAutomaticInfo
Creation on page 6‐51fordetails.)
The
Xpose‐/Xpose+buttonsareashortcutforquicktranspositioninsemitone(halfstep)
increments.YoucanusethemtotransposetheentirePC3LEasmuchasthreeoctavesupor
down.Thetoplineofthedisplayshowsthecurrentamountoftra nsposition(Xpose).Pressing
bothXposebuttonssimultaneouslyreturns
thetranspositiontozero.TheXposebuttons
transposethePC3LE,aswellasanyMIDIdevicesconnectedtothePC3LE’sMIDIOutport.
Changingthetranspositionwiththesoftbuttonsalsochangesthecorrespondingsettingonthe
MastermodeMIDITransmitpage.
Saving Controller Settings
Saving On Program Mode Main Page Vs. The Program Editor
ItisimportanttokeepinmindhowprogramsaresavedwhenontheProgrammodemainpage
vs.whenusingtheProgramEditor.
OntheProgrammodemainpage,ifyouchangethesettingsofanycontrols(knobposition,
assignableswitchon/off,ModWheelposition,aswellasArp
Settings,)theLEDontheSave
buttonwilllight.PresstheSavebuttontobringupthesavedialogandsav eyouredited
program.Ifyouswitchtoadifferentprogram,thealterationsthatyoumadetotheprevious
programwillbelostwithoutwarning.
WhenusingtheProgramEditor,the
LEDontheSavebuttonwilllightwhenyouhavealtered
thecurrentprogram,andthePC3LEwillaskifyouwouldliketosavethecurrentprogramif
youexittheProgramEditor.
Saving A Newly Edited Program
Ifyouaresavingchangestoaprogramthatyouhavenotpreviouslyedited,thesave
dialogwill
choosethefirstavailableuserID#asasavelocation(sothatyoudon’treplacetheoriginal
program.)YoucanalsochooseadifferentID#tosavetheprogramtoandrenametheprogramif
desired.IfyouhaveeditedafactoryROMprogramandwishtosaveover
theoriginalprogram