Lenze 8400 BaseLine C - Page 335

Lenze · 8400 BaseLine C · Reference manual · DMS 1.6 EN · 01/2014 · TD05 335
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C93 249
C94 249
C95 250
C97 250
C98 250
C99 250
C990 296
C991 296
C992 296
C994 297
CA06
CAN CRC error (error message)
164
CA07
CAN bus warning (error message)
164
CA08
CAN bus stopped (error message)
164
CA0b
CAN Bus Live Time (error message)
164
CA0F
CAN control word (error message)
165
CAN baud rate (C00351) 269
CAN data telegram 176
CAN error status (C00345) 268
CAN Heartbeat Producer Time (C00381) 274
CAN IN/OUT COBID source (C00353) 270
CAN input words (C00866) 294
CAN MessageError (C00364) 273
CAN monitoring times (C00357) 271
CAN node address (C00350) 269
CAN NodeID Heartbeat producer (C00385) 275
CAN on board 169
CAN output words (C00868) 295
CAN Slave/Master (C00352) 270
CAN start remote node 182
CAN status (C00359) 272
CAN status HeartBeat producer (C00347) 269
CAN Sync transmission cycle time (C00369) 274
CAN Sync-Rx-Identifier (C00367) 273
CAN Sync-Tx identifier (C00368) 274
CAN telegram counter (C00360) 272
CAN time settings (C00356) 271
CAN transmit blocking time (C00324) 268
CAN_Tx_Rx_Error (C00372) 274
Cause for controller inhibit (C00158) 259
Cause for quick stop QSP (C00159) 260
CE1
CAN RPDO1 (error message)
165
CE2
CAN RPDO2 (error message)
165
CE4
CAN bus off (error message)
164
Checksums (C00516) 280
COB-ID 176
COBID (C00354) 270
COB-ID EMCY (I-1014) 216
COB-ID SYNC message (I-1005) 215
Communication control words (C00136) 254
Communication cycle period (I-1006) 216
Communication time 172
Comparison value N_Act (C00024) 242
Consumer heartbeat time (I-1016) 217
ConsumerTime HeartBeat Producer (C00386) 275
Control mode 73
Control mode (C00007) 238
Conventions used 9
CRC error 206
Current switching frequency (C00725) 289
D
Data type 230
DCB
Current (C00036)
244
Hold time (C00107) 251
DCB (DC-injection braking) 97
DC-bus voltage (C00053) 245
DC-injection braking 96
Deceleration time main setpoint (C00013) 239
Deceleration time quick stop (C00105) 251
Defining current limits 76
Defining speed limits 76
Delayed resp. to fault
DC bus overvoltage (C00601)
284
Device commands (C00002) 235
Device overload monitoring (Ixt) 103
Device rated current (C00098) 250
Device settings (C00141) 255
Device state (C00137) 255
Device type (I-1000) 213
Device utilisation (Ixt) (C00064) 246
Device utilisation threshold (Ixt) (C00123) 253
dF01
Internal error 01 (error message)
166
dF02
Internal error 02 (error message)
166
dF03
Internal error 03 (error message)
167
dF04
Internal error 04 (error message)
167
dF05
Internal error 05 (error message)
167
dF06
Internal error 06 (error message)
167
dF07
Internal error 07 (error message)
167
dF08
Internal error 08 (error message)
168
dF09
Internal error 09 (error message)
168