3-3
Chapter 3 Setup
3
2
2
Screen transition when (ADJUST) key is pressed
When adjustment functions (Feed Comp./ Prop Pos. Correct) are performed, the Adjust menu can be displayed easily without
selecting [MENU]-[Setup] from Local. Press the [SEL] key to display “ADJUST” for [FUNC1], and then press the [FUNC1] key.
Setup menu table
• For each setting item below, you can set it so that the machine may operate according to the value specified when you
printed from your RIP software in the connected host PC.
• Set Item : DRYING Time/ Vacuum Fan
• When you operate the machine according to the contents specified with the RIP software, set each item to “Host” when
registering this machine type. When you set it other than “Host”, the machine operates according to the machine setting.
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name Set value
*1
When no instruc-
tion from RIP
exists
*2
Outline
Feed Comp. ( P.3-6) -9999 to 0
to 9999
Used to print a pattern for correcting a media-
feeding rate and correct it.
Drop Pos. Correct ( P.3-7) -40.0 to 0
to 40.0
Used to adjust the dot position in go and return
printing.
Heater
(P.3-8)
PRINT
OFF
/ 20 to 60 °C
(OFF/ 68 to 140°F)
Sets the print-heater's temperature.
POST 1L
OFF
/ 20 to 60 °C
(OFF/ 68 to 140°F)
Set the temperature of the post heater (1/2) on
the left side.
POST 2L
OFF
/ 20 to 70 °C
(OFF/ 68 to 158°F)
POST 1R
OFF
/ 20 to 60 °C
(OFF/ 68 to 140°F)
Set the temperature of the post heater (1/2) on
the right side.
POST 2R
OFF
/ 20 to 70 °C
(OFF/ 68 to 158°F)
EXTERNAL HEATER ON/OFF Sets ON/OFF of the external heater.
Logical Seek ( P.3-8) Host
/ ON/OFF Sets the scan movable area during printing.
Overprint
(P.3-9) Host / 1 to 9 1
Sets the number of layers in which ink is to be
applied.
Drying Time
(P.3-19)
Scan Host
/0.0 ~ 9.9 sec 0 sec Sets the drying time of ink per scan.
Margin/L ( P.3-9)
Host
/-10 to 0 to 85mm
Sets a non-printing area along the right and
left edges of the media.
Margin/R ( P.3-9)
Refresh ( P.3-10) Host / Lv.0 to Lv.3 Lv.3
Sets the interval of refresh performed during
printing.
Refresh Left ( P.3-20) ON/OFF
OFF
Depending on the type of ink to be used, if the
flushing operation on the capping station can
not fully refresh the head, you can also set to
allow the flushing operation on the left side.
Vacuum Fan ( P.3-10)
Host / OFF/ Weak/
Standard
/ Strong
Standard Sets the absorbability of the media.
Feed Speed ( P.3-10) Host
/ 10 to 200 % Changes the media feeding speed in printing.
MAPS4
(P.3-11)
Auto/ Manual
Perform setting to reduce stripes between
passes.
Manual
Speed 50 to 100 %
Smoothing Lv.
0 to 25 to 100%
Feed Comp.
>
>
PropPos. Correct
Adjust
Feed Comp.
>
>
PropPos. Correct
Adjust
REMOTEMENU
TEST PRINT /
CLEANING
Local <Setup 1>
12:00
1340mm
25°C34°C50°C30°C32°C
PRINT POST 1L POST 2L POST 1R POST 2R
To Next Page
Loading...
