Minebea Intec MiNexx-link-E PR 5215/01 - Page 64

150 pages

To Next Page

To Previous Page

5. Getting started | 5.5 - Connect device to the network | 64

Under [Networking] select the protocol shown and click [Properties].

A window appears.

Main Page

Table of Contents3
Introduction7
Read the Safety Instructions and the Manual7
This Is What Operating Instructions Look Like7
This Is What Lists Look Like7
This Is What Warnings Look Like7
Hotline8
Safety Instructions9
General Instructions9
Intended Use9
Initial Inspection9
Before Operational Startup10
Installation10
Use in Ex Zones10
Opening the Device10
Supply Voltage Connection11
Protective Ground Connection11
RF Interference Suppression11
Failure and Excessive Stress11
Important Note12
Repairs and Maintenance12
Device Description14
Transmitter Types14
General Information14
Pr 5215/0014
Pr 5215/0115
Pr 5215/0416
Pr 5215/0517
Pr 5215/0618
Pr 5215/0719
Pr 5215/0820
Pr 5215/1021
Pr 5215/1122
Overview of the Device23
Communication Protocols23
Housing24
Housing Dimensions24
Indicator Front25
Overview of Connections26
Sticker28
Device Installation29
General Instructions29
Mechanical Preparation30
Storage and Transport Conditions30
Installation Location30
Unpacking31
Checking the Equipment Supplied31
Acclimatizing the Device31
Cable Connection31
EMC-Compliant Installation31
Hardware Construction33
Network Port33
Interface34
Digital Inputs35
Digital Outputs (Relay Outputs)37
Connection of Analog Load Cells and Platforms39
Analog Output47
Profibus-DP Interface49
Devicenet Interface52
CC-Link Interface54
Profinet I/O Interface55
Ethernet/Ip Interface57
Ethercat Interface59
Getting Started61
Switching on the Device61
Switching off the Device61
Device Warm-Up Time61
Power Failure61
Connect Device to the Network62
Connecting Device to the Network Via DHCP62
Connecting Device to the Network Via Static IP Address63
Data Backup66
Overwrite Protection67
CAL Switch67
Performing a Factory Reset on the Device68
Operating69
Operating and Display Elements69
TFT Color Touch Display69
WEB Display70
Message Dialog74
Display Menu75
WEB Menu78
Weighing Points78
Application Settings80
Interfaces80
System83
Service83
Assign Password84
Change Password86
Error Logging in87
Select Language88
Current Date & Time89
Serial Interface90
Digital Inputs & Outputs90
Defining Limits91
Configuring the Analog Output93
Metrology Parameters95
Calibrating Internal Weighing Point98
General Instructions98
Performing a New Adjustment99
Modifying a Adjustment105
Modbus Protocol106
General Description106
SMA Protocol107
General Description107
Fieldbus Interface108
General Notes108
Scale Protocol108
Data Exchange Range109
Reading and Writing Data with Function Numbers112
Reading and Writing Bits Directly114
Waiting for the Result of the Action115
Function Numbers116
Example: Reading the Gross Weight125
Special Note for Devicenet and Ethernet/Ip127
Spm128
General Notes128
Elementary Data Types128
Addressing129
System Data130
Error Messages133
Error Messages Measuring Circuit133
Error Numbers @ "LAST_ERROR134
Weighing Point Error134
Maintenance/Repairs/Cleaning135
Maintenance135
Repairs135
Cleaning136
Instructions for Cleaning136
Safety Inspection137
Disposal138
Specification139
Equipment Supplied139
General Technical Data139
Date/Time Buffer139
Touch Display139
Supply Voltage Connection Version 24 V DC139
Effect of Ambient Conditions140
Ambient Conditions140
Electromagnetic Compatibility (EMC)140
RF Interference Suppression141
Weighing Electronics Data141
Load Cells141
Principle142
Accuracy and Stability142
Sensitivity142
Connecting Cables143
Mechanics143
Housing143
Appendix144
Certificates144
Meu22001144

Minebea Intec MiNexx-link-E PR 5215/01 - Page 64

Table of Contents

Related product manuals