Program
No.
Program Name Input Data Default
15-03-14 Single Line Telephone Basic Data Setup - For-
warded Caller ID Display Mode
0 = Calling Extension Number
(Calling)
1 = External Caller ID (Forward)
0
20-03-01 System Options for Single Line Telephones - SLT
Call Waiting Answer Mode
0 = Hook Flash (Hooking)
1 = Hook Flash + Service Code
794
0
20-03-02 System Options for Single Line Telephones - Ig-
nore Received DP Dial on DTMF SLT Port
0 = Do Not Ignore (No)
1 = Ignore (Yes)
0
20-03-03 System Options for Single Line Telephones - SLT
DTMF Dial to Trunk Lines
0 = Receive all dialed data, be-
fore sending (All)
1 = Direct through out (Direct)
0
20-03-04 System Options for Single Line Telephones - Di-
al Sending Start Time for SLT or ARS
0 ~ 64800 seconds 1
20-03-05 System Options for Single Line Telephones - SLT
Operation Mode
0 = Normal Mode
1 = Extended Mode 1
2 = Extended Mode 2
0
20-03-06 System Options for Single Line Telephones -
Headset Ringing Start Time (for SLT)
0 ~ 64800 seconds 5
20-03-07 System Options for Single Line Telephones -
Trunk Call Dial Forced Sending Start Time
(Forced Dial)
0 ~ 64800 seconds 0
20-06-01 Class of Service for Extensions - Class of Serv-
ice for Extensions
1 ~ 15 Extension 101 is Class
15 and other Extension
are Class 1
20-13-13 Class of Service Options (Supplementary Serv-
ice) - Continued Dialing (DTMF) Signal on ICM
Call
0 = Off
1 = On
COS 01 ~ 15 = 1
20-15-01 Ring Cycle Setup - Incoming Signal Type : Nor-
mal Incoming Call on Trunk
Ringing Cycle Number : 1 ~ 13 3
20-15-03 Ring Cycle Setup - Incoming Signal Type : In-
coming Internal Call
Ringing Cycle Number : 1 ~ 13 3
20-15-05 Ring Cycle Setup - Incoming Signal Type :
DID/DDI
Ringing Cycle Number : 1 ~ 13 8
80-03-01 DTMF Tone Receiver Setup - Detect Level 0 = 0 dBm ~ - 25 dBm
1 = - 5 dBm ~ - 30 dBm
2 = - 10 dBm ~ - 35 dBm
3 = - 15 dBm ~ - 40 dBm
4 = - 20 dBm ~ - 45 dBm
5 = - 25 dBm ~ - 50 dBm
6 = - 30 dBm ~ - 55 dBm
Refer to the Program-
ming Manual for the
default values.
80-03-02 DTMF Tone Receiver Setup - Start Delay Time 0 ~ 255 (0.25 ms ~ 64 ms) Refer to the Program-
ming Manual for the
default values.
80-03-03 DTMF Tone Receiver Setup - Min. Detect Level 0 ~ 15
DTMF Tone 0 = - 10 dBm (0) to -
25 dBm (15)
DTMF Tone 1 = - 15 dBm (0) to -
30 dBm (15)
DTMF Tone 2 = - 20 dBm (0) to -
35 dBm (15)
DTMF Tone 3 = - 25 dBm (0) to -
40 dBm (15)
DTMF Tone 4 = - 30 dBm (0) to -
45 dBm (15)
DTMF Tone 5 = - 35 dBm (0) to -
50 dBm (15)
DTMF Tone 6 = - 40 dBm (0) to -
55 dBm (15)
Refer to the Program-
ming Manual for the
default values.
SL2100 ISSUE 1.0
1-776
Single Line Terminals
S
To Next Page
Loading...
