EasyManuals Logo

NETGEAR WNDAP360 User Manual

NETGEAR WNDAP360
137 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
Installation and Basic Configuration
21
ProSafe Dual Band Wireless-N Access Point WNDAP360
Configure IP Settings and Optional DHCP Server Settings
To configure the IP settings:
1. Select Con
figuration > IP > IP Settings. The IP Settings screen displays:
Figure 10.
2. Specify the fields as explained in the following table:
Table 4. IP Settings
Field Description
DHCP Client By default, the Dynamic Host Configuration Protocol (DHCP) client is disabled. If
you have a DHCP server on your LAN and you select the Enable check box, the
wireless access point will receive its IP address, subnet mask, and default
gateway settings automatically from the DHCP server on your network when you
connect the wireless access point to your LAN.
IP Address Enter the IP address of your wireless access poi
nt. The default IP address is
192.168.0.100. To change the address, enter an unused IP address from the
address range used on your LAN, or enable DHCP the server.
IP Subnet Mask Enter the network number portion of an IP address. Unless you are
imple
menting subnetting, enter 255.255.0.0 as the subnet mask.
Default Gateway Enter the IP address of the ISP’s router to
which the wireless access point will
connect.
Primary DNS Server
Enter the IP address of the primary and secondary DNS servers.
A DNS server is a host on the Internet that
translates Internet names (such as
www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP
address of one or two DNS servers to your wireless access point during login. If
the ISP does not transfer an address, you need to obtain it from the ISP and
enter it manually in this field.
Secondary DNS Server
Network Integrity Check Select this check box to vali
date that the upstream link is active before allowing
wireless associations. Ensure that the default gateway is configured.

Table of Contents

Other manuals for NETGEAR WNDAP360

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR WNDAP360 and is the answer not in the manual?

NETGEAR WNDAP360 Specifications

General IconGeneral
VLAN supportYes
Frequency band2.4 - 5 GHz
Number of users50 user(s)
Cabling technology10/100/1000BASE-T(X)
Ethernet LAN data rates10, 100, 1000 Mbit/s
Maximum data transfer rate1000 Mbit/s
Antenna connector typeSMA
Antenna gain level (max)5 dBi
Weight (imperial)1.93 lbs
Networking featuresGigabit Ethernet
Compliance industry standardsIEEE 802.11a, IEEE 802.11g, IEEE 802.11n, IEEE 802.3af, IEEE802.1x
WAN connectionEthernet (RJ-45)
Ethernet LAN (RJ-45) ports1
Security algorithms64-bit WEP, 128-bit WEP, EAP, EAP-TLS, EAP-TTLS, PEAP, SSH, SSL/TLS, TTLS, WEP, WPA, WPA2
Power requirements12 VDC, 1A
Power consumption (typical)10.51 W
Minimum system requirementsInternet Explorer 6.0, Mozilla Firefox 1.5
Compatible operating systems- Windows Vista, XP, 2000, 98, Me - Mac OS - UNIX - Linux
InternalNo
LED indicatorsLAN
Cable lock slot typeKensington
Weight and Dimensions IconWeight and Dimensions
Height54.76 mm
Weight878 g
Dimensions (WxDxH)253.75 x 253.76 x 54.76 mm

Related product manuals