Nortek 2GIG GC2 - Programming Outline and Compliance; Programming Steps and ANSI;SIA Compliance

Copyright © 2016 Nortek Security & Control 31
Programming Outline
Eachsysteminstalledwillrequireprogramming.Most
installationsbeingperformedbytheprofes sionalalarm
installerforaspecificorganizationwillhavecommonvalues
setineveryControlPanelthatisreportingtotheCentral
Station.Otherprogrammingvalues,suchastheaccount
numberandsensorsetup,maybeuniqueforeach
ins
tallation.
Usethefollowingoutlinetoguideyouthroughthe
installationprocess.UnderstandingtheControlPanel’ s
programmingstructurewillhelptosavetimeduringeach
installation.
Atthisstagethefollowingshouldbealreadycompleted:
•Allhardwiredsensorsinstalled
•Allwi
relesssensorsinstalled
• ControlPanelmounted,connected,andpowered 
up
1 AttheHomescreen,tapthesystemlogointhelower
rightcorner.
Figure 48 The Home Screen
NOTE: YoucanalsotaptheInstallerToolboxbuttonfrom
thesystem’sToolbox(3of3)screen.
2 Entertheinstallercode(thedefaultinstallercodeis
1561)intheEnterYourCodetoAccesstheToolbox
screen.
3 AttheInstallerToolbox,tapSystemConfiguration.
Thenbeginthe"RFSe
nsorProgrammingQue stions"on
page42.
4 Afterprogrammingalloftherequiredsensorsintothe
ControlPanel,tapEnd,thenExit,tosavethechanges.
5 AftertheControlPanelrestarts,tapSecurity>Menu>
Tool box.
6 Whenprompted,enterthemasterusercode.The
defaultmasterusercodeis1111.
7 TaptheUserManagementbuttonandthensetupthe
usercodes.BesuretosetuptheDuressCodeasUser
#8.TapBackwhenfinished.
8 TapBrightness/Volumeandsetthelevelsforthe
installation.
9 Thevolumesettingdoesnotaffectthevolumeofalarm
sounds.
10 Tap→toviewthesecondtoolboxscreen.
11 TapBackLightTimeoutandsetthedisplaylighting
timeout.
12 TapSetDateandSetTimeandsetthecalendarand
clock.IftheGSM(Cellular)RadioModuleisinstalled,
thedateandtimesetsautomatically.
13 Pressthe buttontoreturntotheHomescreen.
Aftercompletingallsetupandprogrammingtasks,referto
theControlPanel’sUserGuideforinformationabout
operatingthesystem.Checkofftheprogrammedoptions
forthesystemintheUserGuide.
NOTE: Ins
tructtheenduseraboutpropersystem
operations,andle avetheUserGuideattheinstallation
siteforreference.
ANSI/SIA CP-01 Compliance
Severalprogrammableoptionshavethedefaultspre‐setto
providecompliancewiththeAmericanNationalStandards
Institutes/SecurityIndustryAssociationCP‐01ControlPanel
Standard.Thetablebelowdetailsthesettingsthatcomply
withANSI/SIACP‐01andpermanentlyprogrammedintothe
Console.TheANSI/SIACP‐01settingsdocumentedinthe
tablebe
lowcannotbechanged:
Programming
Questions
ANSI/SIACP ‐01
Setting Range
Q1>Q:SelectRFSensor#
DialerDelay(0to1)
(1)Enabled (0)Disabledor
(1)Enabled
Q2>Q:SelectWiredSen‐
sorDialerDelay(0to1)
(1)Enabled (0)Disabledor
(1)Enabled
Q5EnterExitDelay,in
Seconds(45‐120)
60Seconds 45‐120Seconds
Q6EnterEntryDelay1,in
seconds(45‐120)
30Seconds 30‐240Seconds
Q7EnterEntryDelay2,in
seconds(45‐120)
45Seconds 30‐240Seconds
Q10EnterCallWaiting
DisableCode(0‐6digits)
NoDefaultCode 0‐6Digits
Q20SelectSwingerShut‐
downCount(1to6)
(2)TwoTrips 1‐6Trips
Q26SelectAutoStay
(0to1)
(1)Enabled (0)Disabledor
(1)Enabled
Q27ExitDelayRestart
(0to1)
(1)Enabled (0)Disabledor
(1)Enabled
Q31EnterCancelTime,in
Minutes(5‐255)
5Minutes 6‐254Minutes
Q32SelectCancel
Display(0to1)
(1)Enabled (0)Disabledor
(1)Enabled
Q35SelectAbortWin‐
dowDialerDelay(0to2)
30Seconds 15to45Seconds
Q78SelectOutput (11)Follows
InternalSounder
Alarm
NOTE:See"Q78:
Output"on
page61