Nortek 2GIG GC2 - Q18: Emergency Key (0-1); Q19: Quick Arming (0-1); Q20: Swinger Shutdown Count (1-6); Q21: Siren Supervision Time (0-3)

Go!ControlWirelessSecuritySystem|InstallationandProgrammingGuide
54Copyright©2016NortekSecurity&Control
•Todisableandnotdisplaythefireemergency
button,select(0)Disabled.
Q18: Emergency Key (0-1)
DEFAULT:(1)Audible
TheControlPanel’ semergencybuttoncanbeenabledor
disabled.Thepanel’ semergencybuttonisdisplayedby
pressingtheEmergencybuttononthepanel.
•Thede
faultsetting(1)Audiblesoundsanaudible
alarmwhenthebutt on ispressed.
•Todisab
lethisbutton,select(0)Disabled.
NOTE: Ifallthr
ee(3)Emergencybuttonsaredisabled,the
ControlPaneldisplaysamessagewhenitsEmergency
buttonispressed.
Q19: Quick Arming (0-1)
DEFAULT:(1)Enabled
Quickarmingallowsthesubscribertoarmthesystem
withouthavingtoenterausercode.IfOpen/CloseReports
arebeingsent,quickarmingisreportedasUser0.
•Thede
fault(1)Enabledallowsquickarming.
•Toturnof
fquickarming,select(0)Disabled.
Q20: Swinger Shutdown Count (1-6)
DEFAULT:(2)TwoTrips
Theminimumsettingof(2)TwoTripsisrequiredforANSI/
SIACP‐01compliance.Thisdefaultsettingcanbeincreased
tothreeormoretripswithoutaffectingANSI/SIACP‐01
compliance.
Anunwantedseriesofmultiplefaults(usuallycausedbya
badcontactorsensor)iscalleda“s
winger. ”Swinger
shutdownsetsthemaximumnumberofalarmsthatany
sensororhardwireloopcantriggerduringasinglearming
period.
NOTE: COan
dSmokedetectoralarmsarenotlimitedby
theswingershutdowncount.Othertypesof24‐hour
zonesarelimitedbytheswingershutdowncount.
•Thede
faultsetting(2)Two‐Tripssetstheswinger
shutdowncountattwo(2)trips.
•Toch
angethiscount,select(1‐6).
Q21: Siren Supervision Time (0-3)
DEFAULT:(0)Disabled
Thewiringconnectiontotheexternalsoundercanbe
supervised.Ifthewiringtothesounderiscutfor15,30,or
45seconds,abelltroublereportcanbesenttotheCentral
Station.
•Thede
faultsetting(0)Disabledturnsexternal
soundersupervisionOFF.
•Tosu
pervisetheexternalsounderwiring,select:
•(1)15Sec
onds
•(2)30Sec
onds
• (3)45Sec
onds
Q22: CS Lack of Usage Notification Time
(0-255)
DEFAULT:7days
Ifthissystemhasnotbeenarmedforaspecifiednumberof
days,inactivityreportscanbesenttotheCentralStation.
•Thede
faultsettingis7days.
•Toch
angetheduration,selectavaluebetween1to
255days.
•Toturnth
isfeatureOFF,select0days.
Q23: Radio Modem Network Failure Time
(0-255)
DEFAULT:30Minutes
NOTE: GSM(Ce
llular)RadioModulemustbeinstalledto
usethisfunction.
Iftheoptio
nalGSM(Cellular)RadioModulelosesits
cellularconnection,specifytheamountofdowntimethat
mustpassbeforetriggeringatroublecondition.
•Thede
faultsettingis30minutes.
•Tospecifyadifferentamountoftime,enteravalue
betweenone(1)to255minutes.
•Toturnth
isfeatureOFF,select0minutes.
NOTE: Aft
ercellularserviceisrestoredforfive(5)minutes,
thetroubleconditionautomaticallyclear s .
Q24: Radio Modem Network Failure
Causes Trouble (0-1)
DEFAULT:(1)Enabled
NOTE: GSM(Ce
llular)RadioModulemustbeinstalledto
usethisfunction.
SelectswhethertheCon
trolPanelwillsoundanddisplay
troubleiftheoptionalGSM(Cellular)RadioModulehaslost
itscellularconnection.Thetroublesoundercanbesilenced
bytheuserattheControlPanel(cellradiotroubleislogged
regardlessofthissetting).Whenthecellularradiomodule
connectionisrest
ored,thetroubleindications
automaticallyclear.
•Thede
fault(1)Enabledallowsradiomodulefailure
troubleindications.
•Toturnoffra
diomodulefailuretroubleindications,
select(0)Disabled.
Q25: Radio Modem Network Failure
Reports (0-1)
DEFAULT:(1)Enabled
NOTE: GSM(Ce
llular)RadioModulemustbeinstalledto
usethisfunction.
Iftheoptio
nalGSM(Cellular)RadioModulelosesits
cellularconnection,theControlPanelcanreportthefault
andrestorevialand‐lineiftelephonereportingisenabled.
•Thede
fault(1)Enabledallowsradiomodulefailure/
restorereporting.
•Toturnoffra
diomodulefailure/restorereporting,
select(0)Disabled.
Q26: Auto Stay (0-1)
DEFAULT:(1)Enabled
ThisfeaturemustbeenabledforANSI/SIACP‐01compliance