Nortek 2GIG GC2 - Installer Programming - Core Tasks; Account Registration and RF Sensor Setup

Copyright © 2016 Nortek Security & Control 41
Installer Programming
Account Registration
RegistertheaccounttoenrolltheControlPanelwiththe
remoteserviceprovider’sCentralStation.
Typically,theaccountregistrationdataiscreatedwiththe
serviceinstallationcontractandthenstoredinadatabase
managedbytheCentralStation.Thedataincludesitems
suchasthecustomername,address,andtheCentral
Stationtelephonenumber,andtheaccountnumber
assignedtotheControlPanel.
Ifyouwillbeinstallingthe2GIGGo!BridgeIP
Communicator,additionalregistrationinformationis
required.Fordetails,seetheInstallationInstructions
includedwiththeGo!BridgeIPCommunicator.
Wireless (RF) Sensor Programming
TheControlPanelcanbeprogrammedwithupto60RF
sensorsofdifferenttypes.Inadditiontothe60multi‐
purposeRFsensors,youcanalsoprogrameight(8)RF
remotecontrolkeyfobsandfour(4)RFremotecontrol
keypadsintothesystem.
RFsensors#01‐48and
#63‐74reportaswirelesszones01‐
60.
ProgrammingquestionsforRFsensorprogramming
include:
• Q1:SelectRFSensorNumber.Selectsensornumber
01‐48or63‐74.
• Q:SelectRFSensor#Type.Select(01)Exit/Entry1,
(02)Exit/Entry2,(03)Perimeter,andsoon.For
options,see
"ZoneNumbering"onpage35.
• Q:SelectRFSensor#EquipmentType.Some
sensortypesaskfortheequipmenttype,othersdo
not.See"Q:SelectRFSensor#EquipmentType"on
page43.
• Q:SelectRFSensor#EquipmentCode.Selectthe
four(4)‐digitequipmentcodeforthesensormodel.
See"EquipmentCodes"onpage40.
• Q:EnterRFSensor#OtherEquipmentCode.Ifyou
select(0000)Otherinthepreviousquestion,you
mustenterthiscode.
• Q:EnterRFSensor#Serial#.Entertheserial
number(typicallyalabelonthesensororits
packaging)ortapShiftthenLearnonthepanel.
Thentripthesensortotransmittheserialnumber
tothepanel.
• Q:SelectRFSensor#EquipmentAge.Specify
whetherthesensoris(0)Newor(1)Existing.
• Q:SelectRFSensor#LoopNumber.Specifythe
appropriateloopnumber(s)forthesensor.See
"Q:
SelectRFSensor#LoopNumber(1to3)"onpage
43.
• Q:SelectRFSensor#DialerDelay.Specifywhether
tousedelayedorinstantdigitalcommunicator
reportsforthesensor.Thedelaytimeissetonthe
DialerAbortscreen.
• Q:ConstructRFSensor#VoiceDescriptor.Specify
thenameassignedtothesensorthatisannounced
ifthisfeatureisprogrammed.
• Q:SelectRFSensor#Reports.Specify(0)Disabled
or(1)EnabledwhetherornotRFsensorstriggera
reporttotheCentralStation.
• Q:SelectRFSensor#Supervised.Specifywhether
ornottheControlPanelchecksforstatusreports
fromthesensor.
• Q:RFSensor#Chime.Selectvoiceannouncement
andchimeoptionsforthesensor.