Nortek 2GIG GC2 - Q89: Allow Backlight Always on (Demo Mode) (0-1); Q90: Energy Feature (0 to 1); Q91: Radio Modem Supplier; Q92: Select Network Device (0 to 1)

Control Panel Programming
Copyright © 2016 Nortek Security & Control 63
Q89: Allow Backlight Always On (Demo
Mode) (0-1)
NOTE: Maycauseghost/imageretention.
DEFAULT:(0)Disable
d
Whensetto(1)Enabledthecustomercanprogr amthe
“alwayson”optionforbacklightprogramming.Duetoa
smallpercentageofimage“ghosting”onthepanel
(becausethebacklightnevergoesoff),thisquestionwas
beencreatedbuthasbeendefaultedto(0)Disabled.
Q90: Energy Feature (0 to 1)
DEFAULT:(0)DisabledandHidden
Select(1)DisabledbutVisibletoshowbutnotactivatethe
energyfeatures.Youcanalsoselect(2)Enabledtoturnthe
energyfeatureON.
Q91: Radio Modem Supplier
DEFAULT:(0)NoRadioModemSupplier
NOTE: IfyouenableQ44:SelectLockInstaller
Programming,youwillnotbeabletochangethis
setting.
NOTE: ForcompliancewithUL1610,Q91:SelectRadio
ModemSupplier(0to5)mustbesetto(1)Radio
ModemSupplier1.
Selecttheoptionthatcorrespondstotheappropriate
supplier.Optionsinclude:
Q92: Select Network Device (0 to 1)
DEFAULT:(0)None
Whenenabled,the(1)Go!Bridgeoptionprovidesthe
installerwiththefollowingquestionstoprogramthe
Go!BridgeIPCommunicatorsettingsintotheControlPanel
Q: Network Device ID (read only)
TapLearn.ThengototheGo!Bridgedeviceandtapthe
Learnbutton.Fordetails,seetheGo!BridgeIP
CommunicatorInstallationInstructions.
Q: Select Configuration Source
Default:(0)DHCP
Selectbetween(1)Staticor(2)DHCP(DynamicHost
ConfigurationProtocol).Thedefaultsettingis(0)DHCPand
isthemostcommonselection.Theotheroptionis(1)Static
andrequiresentryofaDeviceIPAddress,GatewayIP
Address,andSubnetMask.
Q: Enter Device IP Address
Default:000.000.000.00
0
NOTE: Thisque
stiononlyrequiresananswerifyouselected
(1)StaticinQ:SelectConfigurationSource.
Usethenu
merickeypadtoentertheIPAddressforthe
Go!BridgeIPCommunicator.
Q: Enter the Gateway IP Address
Default:000.000.000.0
00
NOTE: Thisque
stiononlyrequiresananswerifyouselected
(1)StaticinQ:SelectConfigurationSource.
Usethenu
merickeypadtoentertheIPAddressforthe
accesspointtotheexternalnetwork.Typically,thisistheIP
Addressofthelocalnetworkrouter.
Q: Enter the Subnet Mask
Default:000.000.000.0
00
NOTE: Thisque
stiononlyrequiresananswerifyouselected
(1)StaticinQ:SelectConfigurationSource.
Usethenu
merickeypadtoentertheIPAddressforthe
subnetmaskforthenetwork.
Q: Select Port # (1 to 8)
DEFAULT:(1)Port1
NOTE: Ty
pically,youwillskipthisquestionunlessadditional
programmingisrequired.
Selecttheportnu
mberforthebackendserver.After
configuringtherequiredport,tapNextontheControl
Panel.
•(1)Po
rt1
•(2)Po
rt2
•(3)Po
rt3
•(4)Po
rt4
•(5)Po
rt5
•(6)Po
rt6
•(7)Po
rt7
• (8)Po
rt8
Q: Select Used (0 to 1)
DEFAULT:(0)Disabled
NOTE: Ty
pically,youwillskipthisquestionunlessadditional
programmingisrequired.
Itisre
commendedthatyoualwaysselectthedefault
setting(0)Disabled.Ifyouchoose(1)Enabled,youwillbe
promptedtoentertheportvalue.
Q: Enter Port Value (0 to 65535)
DEFAULT:(0)Dis
abled
NOTE: Ty
pically,youwillskipthisquestionunlessadditional
programmingisrequired.
Itisre
commendedthatyoualwaysselectthedefault
setting(0)Disabled.Ifyouselect(1)EnabledinQ:Select
Used(0to1),usethenumerickeypadtoentertheport
value.
NOTE: Theportvalueistheportnu
mberforTransmission
ControlProtocol(TCP)communication.Portnumbers
canrangefrom0to65535.
Option Supplier
(0)NoRadioModemSupplier Thisisthedefaultsetting.
(1)RadioModemSupplier1Alarm.com
(2)RadioModemSupplier2 Telular
(3)RadioModemSupplier3
(4)RadioModemSupplier4
(5)RadioModemSupplier5
(6)RadioModemSupplier6